+966 54 614 8678 [email protected] WhatsApp
JTE FastenersBolting & hardware, Al Jubail العربية Request a quote

Fastener FAQ: answers on bolting, grades and supply in Saudi Arabia

Short, sourced answers on stud bolts, nuts, coatings, certificates, Saudi Aramco and SABIC requirements and ordering, each linked to the page with the detail.

This page collects 282 answers from across the JTE Fasteners site, grouped by topic. Each answer links to the page it comes from, where you will find the tables, standards and Saudi requirements behind it. If your question is not here, send it to us and an engineer will answer.

Topics

Stud bolts and grades

Why use duplex stud bolts instead of 316 (B8M)?

Duplex has about twice the yield strength of solution-treated 316 and much better resistance to chloride pitting and stress corrosion cracking, which is why it is preferred in warm seawater and coastal service.

From Duplex and super duplex stud bolts

What is the difference between duplex and super duplex?

Super duplex (UNS S32750, S32760) has more chromium, molybdenum and nitrogen, giving a PREN of at least 40 against about 34 to 36 for duplex 2205. Super duplex is the usual choice for seawater.

From Duplex and super duplex stud bolts

What is PREN?

Pitting Resistance Equivalent Number: %Cr + 3.3 × %Mo + 16 × %N. It ranks stainless steels by resistance to pitting in chlorides.

From Duplex and super duplex stud bolts

Does Saudi Aramco accept duplex bolting?

SAES-L-109 accepts corrosion-resistant alloys as a way to protect bolting in aggressive external environments such as offshore and underground service. Use duplex where the project specification calls for it.

From Duplex and super duplex stud bolts

Which nuts go with duplex studs?

Nuts of the same duplex or super duplex grade, so the joint has matching strength and corrosion resistance and no galvanic mismatch.

From Duplex and super duplex stud bolts

Is duplex suitable for high temperature?

No. Duplex is normally limited to moderate temperatures because it can embrittle when held hot. Use B16 or A453 660 for high-temperature joints.

From Duplex and super duplex stud bolts

What is ASTM A453 Grade 660?

It is the ASTM specification for high-temperature bolting made from A-286 (UNS S66286), an iron-nickel-chromium superalloy, precipitation hardened to a minimum tensile strength of 130 ksi.

From ASTM A453 Grade 660 stud bolts

What is the difference between Class A, B, C and D?

All have 130 ksi minimum tensile strength. Classes A, B and C have 85 ksi minimum yield and differ in heat treatment; Class D has 105 ksi minimum yield.

From ASTM A453 Grade 660 stud bolts

When is A453 660 used instead of B16?

Where the equipment or project specification calls for it: typically turbine casings, hot joints beyond the B16 range, or where a non-magnetic, corrosion-resistant bolt is needed.

From ASTM A453 Grade 660 stud bolts

Is A453 660 magnetic?

No. A-286 is austenitic and essentially non-magnetic.

From ASTM A453 Grade 660 stud bolts

Does Saudi Aramco list A453 660 in SAES-L-109?

The 2018 edition of SAES-L-109 lists B7, B7M, L7, L7M and B16 for piping service classes. A453 660 is supplied where the equipment or project specification names it.

From ASTM A453 Grade 660 stud bolts

Can you make A453 660 replacement studs to a sample?

Yes. We machine replacements to the OEM drawing or a sample and confirm the grade and class on the certificate.

From ASTM A453 Grade 660 stud bolts

What is the difference between B8 and B8M?

B8 is type 304 stainless; B8M is type 316, which contains molybdenum and resists chlorides and pitting better. B8M is usually preferred near the sea and in chemical service.

From ASTM A193 B8 and B8M stud bolts

What is the difference between Class 1 and Class 2?

Class 1 is solution treated, with a minimum tensile strength of 75 ksi. Class 2 is strain hardened for higher strength, up to 125 ksi for B8 and 110 ksi for B8M at 3/4″ and below, falling with diameter.

From ASTM A193 B8 and B8M stud bolts

Which nuts go with B8 and B8M studs?

ASTM A194 grade 8 nuts for B8 and grade 8M nuts for B8M.

From ASTM A193 B8 and B8M stud bolts

Does Saudi Aramco allow stainless stud bolts?

SAES-L-109 lists B7 / 2H for general service and accepts corrosion-resistant alloys as a way to protect bolting in aggressive external environments. Use stainless where the project specification calls for it.

From ASTM A193 B8 and B8M stud bolts

Are 316 stud bolts safe in the Gulf climate?

In hot, chloride-rich conditions, 304 and 316 can suffer chloride stress corrosion cracking. For seawater and hot coastal service, duplex or super duplex is often a safer choice.

From ASTM A193 B8 and B8M stud bolts

How do I stop stainless studs galling?

Use an anti-seize compound suitable for stainless, tighten at a steady speed, or use a coated nut. Do not reuse galled studs.

From ASTM A193 B8 and B8M stud bolts

When should B16 be used instead of B7?

When the bolting runs above about 450 °C. Saudi Aramco SAES-L-109 lists B7 up to 450 °C and B16 with A194 grade 4 nuts from 450 °C to 645 °C.

From ASTM A193 B16 stud bolts

Which nut goes with a B16 stud?

An ASTM A194 grade 4 heavy hex nut is listed in SAES-L-109; grade 7 is also used where the project specifies it.

From ASTM A193 B16 stud bolts

Is B16 stronger than B7?

At room temperature the minimum strength is the same up to 2-1/2″. The advantage of B16 is that it resists relaxation at high temperature.

From ASTM A193 B16 stud bolts

Can B16 studs be PTFE coated?

Fluoropolymer coatings are not meant for B16 service temperatures. B16 is normally supplied plain and assembled with a suitable high-temperature anti-seize.

From ASTM A193 B16 stud bolts

Are Belleville washers needed with B16?

SAES-L-109 says Belleville washers may be required for severe cyclic service and bolt temperatures above 450 °C, subject to review. Follow the joint design.

From ASTM A193 B16 stud bolts

What is used above the B16 range?

A453 grade 660 (A-286) or nickel alloy bolting, as set by the project specification.

From ASTM A193 B16 stud bolts

What is the difference between A320 L7 and A193 B7?

Both are Cr-Mo steel with similar strength, but L7 is Charpy impact tested at −101 °C so its toughness at low temperature is proven. B7 has no impact requirement and is used for general service above about −40 °C.

From ASTM A320 L7 and L7M stud bolts

What is L7M?

L7M is the hardness-limited version of L7 (maximum 235 HB), impact tested at −73 °C, for low-temperature sour service. It is used with A194 7M nuts.

From ASTM A320 L7 and L7M stud bolts

Which nuts go with L7 studs?

ASTM A194 grade 4 or grade 7 heavy hex nuts. For L7M studs, A194 grade 7M nuts.

From ASTM A320 L7 and L7M stud bolts

What does auto-refrigeration mean for bolting?

When light hydrocarbons such as LPG leak through a flange, they can flash and cool the joint far below ambient. Saudi Aramco SAES-L-109 requires low-temperature bolting for flanges exposed to that risk.

From ASTM A320 L7 and L7M stud bolts

What temperature range does Saudi Aramco allow for L7?

SAES-L-109 (2018 edition) lists A320 L7 with A194 4 or 7 nuts from −101 °C to 343 °C, and L7M with 7M nuts from −73 °C to 450 °C. Check the current revision for your project.

From ASTM A320 L7 and L7M stud bolts

Can L7 studs be coated?

Yes. Ceramic-fluoropolymer or PTFE coatings are commonly applied, and the coating cure does not affect the impact properties.

From ASTM A320 L7 and L7M stud bolts

What is the difference between B7 and B7M stud bolts?

Both are ASTM A193 chromium-molybdenum steel. B7M is tempered to keep hardness at or below 235 HB and each piece is hardness tested, so it resists sulphide stress cracking in sour service. B7M has lower strength: 100 ksi minimum tensile against 125 ksi for B7.

From ASTM A193 B7M stud bolts

Which nut goes with a B7M stud?

An ASTM A194 Grade 2HM heavy hex nut, which is also hardness-limited for sour service.

From ASTM A193 B7M stud bolts

Does Saudi Aramco require B7M for sour service?

Saudi Aramco SAES-L-109 lists A193 B7M studs with A194 2HM nuts for wet sour service, where the bolting is in direct or potential exposure to the sour fluid. Always follow the current revision and your project specification.

From ASTM A193 B7M stud bolts

Can B7M stud bolts be coated?

Yes. Ceramic-fluoropolymer or PTFE coatings are cured far below the B7M tempering temperature, so hardness does not change. SAES-L-109 lists ceramic-fluoropolymer coating per 09-SAMSS-107 for bolting in aggressive external environments.

From ASTM A193 B7M stud bolts

Can I use the same torque for B7M as for B7?

No. B7M has a lower yield strength, so the bolt load and torque must be set for B7M, and checked against the flange joint design.

From ASTM A193 B7M stud bolts

How do I identify a B7M stud on site?

The stud end is marked B7M and the nut 2HM. Unmarked or B7-marked bolting should not be used in a sour-service joint.

From ASTM A193 B7M stud bolts

What is a Xylan coated stud bolt?

It is a stud bolt and its nuts finished with a Xylan-type fluoropolymer (PTFE) coating over a phosphate pretreatment. The coating protects against corrosion and lowers friction so the nuts can be removed easily.

From PTFE coated stud bolts

Why are coated stud bolts usually blue?

Blue is the most common standard colour for fluoropolymer-coated flange bolting. Other colours such as green, red or black are used for colour coding by grade or service.

From PTFE coated stud bolts

Do PTFE coated studs need a different torque?

Yes. The coating lowers friction, so the same torque gives more preload than on an uncoated stud. Use a torque value calculated for the coated friction factor or set out in your bolting procedure.

From PTFE coated stud bolts

PTFE coated or hot-dip galvanized: which is better for flanges?

For process flanges that will be opened again, PTFE is usually preferred because it does not gall and keeps thread fit tight. Hot-dip galvanizing gives a thicker coat but needs oversize-tapped nuts and suits permanent structural bolting better.

From PTFE coated stud bolts

Does the coating change the strength of B7 or B7M studs?

No. The coating is cured at temperatures well below the tempering temperature of B7 and B7M, so strength and hardness are unchanged.

From PTFE coated stud bolts

Can you coat studs to a Saudi Aramco or SABIC coating specification?

Yes. We are a registered Saudi Aramco and SABIC vendor and coat to the system, colour, thickness and test requirements in the project specification.

From PTFE coated stud bolts

Is A193 B7 the same as AISI 4140?

B7 is made from AISI 4140, 4142 or 4145 steel, but the grade also requires quench-and-temper heat treatment, minimum tensile and yield strengths, hardness limits and marking. A 4140 bar is not B7 until it meets those requirements and is certified to A193.

From ASTM A193 B7 stud bolts

What is the maximum temperature for B7 bolts?

B7 is generally used up to about 450 °C (840 °F); above that, its strength falls and it relaxes by creep, so A193 B16 or A453 660 is specified. Below about −29 °C, use impact-tested A320 L7.

From ASTM A193 B7 stud bolts

Can B7 be used in sour service?

Not where the bolting can be exposed to the sour environment. NACE MR0175 / ISO 15156 limits hardness for those bolts, so B7M studs with 2HM nuts are used. The project specification decides which joints need it.

From ASTM A193 B7 stud bolts

Is B7 bolting magnetic?

Yes. B7 is a ferritic alloy steel and is magnetic. If a non-magnetic bolt is needed, A453 660 or austenitic stainless grades are used.

From ASTM A193 B7 stud bolts

Can I use B7 studs with 2HM nuts?

A 2HM nut on a B7 stud is not a sour-service joint, because the B7 stud is not hardness-limited. Use B7M studs with 2HM nuts wherever sour-service limits apply.

From B7 vs B7M

Is B7M weaker than B7?

Yes. B7M has a minimum tensile strength of 100 ksi and yield of 80 ksi, against 125 ksi and 105 ksi for B7 up to 2-1/2 inches. That is the price of the lower hardness needed for sour service.

From B7 vs B7M

Is B7M always required in sour plants?

Only for bolting that can be exposed to the sour environment, as defined by NACE MR0175 / ISO 15156 and the project specification. Bolts on joints that cannot see H2S may stay B7.

From B7 vs B7M

How many bolts does a 6 inch Class 150 flange have?

Eight stud bolts of 3/4 inch diameter, each 4 inches long for a raised-face joint, with two heavy hex nuts per stud.

From ASME B16.5 flange bolt chart

How many bolts does a 4 inch Class 300 flange have?

Eight stud bolts of 3/4 inch diameter, 4-1/2 inches long for a raised-face joint.

From ASME B16.5 flange bolt chart

Are stud bolt lengths the same for RTJ flanges?

No. Ring type joint flanges need longer studs than raised-face flanges of the same size and class, because the faces are further apart with the ring fitted. Send the facing with your enquiry.

From ASME B16.5 flange bolt chart

What grade of stud is used on B16.5 flanges?

The piping specification decides, but ASTM A193 B7 studs with A194 2H nuts are the most common, B7M with 2HM for sour service and A320 L7 with A194 7 for low temperature.

From ASME B16.5 flange bolt chart

What is a stud bolt?

A stud bolt is a threaded rod, usually threaded along its full length, that is used with a heavy hex nut on each end to clamp pipe flanges, valve bonnets and pressure-vessel joints. Stud bolts for process piping are most often made to ASTM A193 B7 with ASTM A194 2H nuts.

From Stud bolts

Which nut goes with an A193 B7 stud bolt?

An ASTM A194 Grade 2H heavy hex nut. For B7M studs in sour service the matching nut is A194 2HM, and for L7 low-temperature studs it is A194 Grade 4 or 7.

From Stud bolts

How is stud bolt length measured?

We quote length as the effective length between the first full threads, excluding the chamfered points, which is how the ASME B16.5 bolting tables state it. If your drawing gives overall length including points, say so on the enquiry.

From Stud bolts

Do you supply stud bolts as flange sets?

Yes. We supply stud bolts with two nuts per stud and can pack and tag them per flange joint or line number for shutdowns and new construction.

From Stud bolts

Nuts and nut compatibility

Can I use a 2H nut on a B7M stud?

No. B7M is used for sour service, where hardness is limited to 22 HRC. A 2H nut can be up to 38 HRC, so the matching nut is 2HM.

From Nut compatibility chart for stud bolts and bolts

Which nuts are compatible with ASTM A193 B7?

A194 2H is the standard pair; A194 Grade 4 and Grade 7 nuts are also compatible. Saudi Aramco SAES-L-109 names 2H.

From Nut compatibility chart for stud bolts and bolts

Which nut goes with A320 L7 in cold service?

A194 Grade 7 (or Grade 4) with supplementary requirement S3 Charpy testing, marked 7L or 4L.

From Nut compatibility chart for stud bolts and bolts

Do flange stud bolts need washers?

Usually not. Saudi Aramco SAES-L-109 section 13.4.1 calls for flat washers only in special cases, such as insulating and plastic flanges.

From Nut compatibility chart for stud bolts and bolts

Which nut goes with an A325 structural bolt?

ASTM A563 DH (or A563M 10S in metric), with an F436 hardened washer, as Saudi Aramco 12-SAMSS-007 specifies.

From Nut compatibility chart for stud bolts and bolts

Which nut class goes with a 10.9 metric bolt?

Property class 10 to ISO 898-2.

From Nut compatibility chart for stud bolts and bolts

What is an ASTM A194 7M nut?

A hardness-limited heavy hex nut of quenched and tempered chromium-molybdenum alloy steel, 159–237 HB (22 HRC maximum), with a 150 ksi proof stress, used with A320 L7M studs.

From ASTM A194 7M heavy hex nuts

When is 7M used instead of Grade 7?

When the bolting must also resist sulfide stress cracking: 7M is limited to 22 HRC, while Grade 7 can reach 38 HRC.

From ASTM A194 7M heavy hex nuts

Which stud goes with a 7M nut?

ASTM A320 L7M.

From ASTM A194 7M heavy hex nuts

What temperature range does L7M / 7M cover in SAES-L-109?

About −73 to 450 °C, in Table 5.

From ASTM A194 7M heavy hex nuts

Is 7M the same as 2HM?

Both are limited to 237 HB with a 150 ksi proof stress, but 7M is chromium-molybdenum alloy steel for low-temperature service, while 2HM is carbon steel for B7M studs.

From ASTM A194 7M heavy hex nuts

What is an ASTM A194 Grade 7 nut?

A heavy hex nut of quenched and tempered chromium-molybdenum alloy steel, 24–38 HRC with a 175 ksi proof stress, used mainly with A320 L7 low-temperature studs.

From ASTM A194 Grade 7 heavy hex nuts

What is the difference between Grade 7 and 7L?

7L is a Grade 7 nut that has passed Charpy impact testing under A194 supplementary requirement S3; the L is added to the marking.

From ASTM A194 Grade 7 heavy hex nuts

What is the difference between Grade 7 and 7M?

7M is hardness-limited (159–237 HB, 22 HRC maximum) and tempered at 1150 °F for sour or cold sour service, with a 150 ksi proof stress. Grade 7 is 24–38 HRC with 175 ksi.

From ASTM A194 Grade 7 heavy hex nuts

Which studs take Grade 7 nuts?

A320 L7, A193 B16 and A193 B7.

From ASTM A194 Grade 7 heavy hex nuts

Can Grade 7 replace Grade 4?

ASTM names Grade 7 as the substitute for Grade 4, which was removed from A194 in 2017. On Saudi Aramco work, confirm with the owner, because SAES-L-109 still names Grade 4.

From ASTM A194 Grade 7 heavy hex nuts

Is A194 Grade 4 still a valid grade?

ASTM removed Grade 4 from A194 in 2017. It is still named in older specifications and in Saudi Aramco SAES-L-109 Table 5, so purchase orders may still call for it; the order should name the edition.

From ASTM A194 Grade 4 heavy hex nuts

What replaced A194 Grade 4?

Grade 7. ASTM named it as the substitute; both have a hardness of 24–38 HRC and a proof stress of 175 ksi.

From ASTM A194 Grade 4 heavy hex nuts

Which studs use Grade 4 nuts?

A193 B16 for high temperature and A320 L7 for low temperature.

From ASTM A194 Grade 4 heavy hex nuts

Can I use Grade 7 instead of Grade 4 on a Saudi Aramco job?

Technically they are interchangeable, but SAES-L-109 Table 5 names Grade 4, so get the owner’s or engineer’s approval before substituting.

From ASTM A194 Grade 4 heavy hex nuts

What does an L in a nut marking mean?

The nut has passed Charpy impact testing to A194 supplementary requirement S3 for low-temperature service, for example 4L or 7L.

From ASTM A194 Grade 4 heavy hex nuts

What is an ASTM A194 2HM nut?

A hardness-limited heavy hex nut of quenched and tempered medium carbon steel, 159–237 HB (22 HRC maximum), with a 150 ksi proof stress, used with B7M studs in sour service.

From ASTM A194 2HM heavy hex nuts

Why does sour service need 2HM instead of 2H?

Hard steel can crack under stress in wet H2S (sulfide stress cracking). Limiting hardness to 22 HRC, as NACE MR0175 / ISO 15156 requires, makes 2HM resistant; a 2H nut can be up to 38 HRC.

From ASTM A194 2HM heavy hex nuts

Which stud goes with a 2HM nut?

ASTM A193 B7M, which is also hardness-limited.

From ASTM A194 2HM heavy hex nuts

Is a 2HM nut weaker than a 2H nut?

Yes: its proof stress is 150 ksi against 175 ksi. B7M studs also have a lower minimum yield (80 ksi) than B7 (105 ksi), so the joint is designed and tightened for that.

From ASTM A194 2HM heavy hex nuts

Does Saudi Aramco require 2HM on every sour line?

No. SAES-L-109 section 13.2.3 requires wet sour bolting only where the bolts are directly or potentially exposed to the fluid.

From ASTM A194 2HM heavy hex nuts

How is a 2HM nut marked?

With “2HM” and the manufacturer’s identification mark.

From ASTM A194 2HM heavy hex nuts

What is an ASTM A194 2H nut?

A heavy hex nut of quenched and tempered medium carbon steel, with a hardness of 24–38 HRC and a proof stress of 175 ksi, made to ASTM A194 for high-pressure and high-temperature bolting.

From ASTM A194 2H heavy hex nuts

Which stud bolt goes with a 2H nut?

ASTM A193 B7. Saudi Aramco SAES-L-109 pairs B7 studs with 2H nuts for general service; Grade 7 nuts are also compatible with B7.

From ASTM A194 2H heavy hex nuts

Can 2H nuts be used in sour service?

Not normally. Sour service needs hardness-limited nuts: Grade 2HM (22 HRC maximum) with B7M studs, per NACE MR0175 / ISO 15156 and SAES-L-109.

From ASTM A194 2H heavy hex nuts

What is the difference between 2H and 2HM?

2HM is tempered hotter (1150 °F against 850 °F), so its hardness stays at or below 237 HB / 22 HRC and every nut is hardness tested. 2H is harder and stronger, with a 175 ksi proof stress against 150 ksi. See 2H vs 2HM.

From ASTM A194 2H heavy hex nuts

Can 2H nuts be galvanized?

Yes. Galvanized nuts are tapped oversize so they still fit a galvanized stud, as 12-SAMSS-007 requires for galvanized nuts. Confirm your specification allows a galvanized finish.

From ASTM A194 2H heavy hex nuts

How are 2H nuts marked?

With “2H” and the manufacturer’s identification mark on one face.

From ASTM A194 2H heavy hex nuts

Can 2H nuts be used with B7M studs?

Not in sour service. A 2H nut can be harder than the sour-service limit, so NACE MR0175 / ISO 15156 joints use 2HM nuts with B7M studs.

From A194 2H vs 2HM nuts

Why is the proof stress of 2HM lower?

Lower hardness means lower strength. 2HM is tempered to stay at or below 237 HB, which reduces its proof stress to 150 ksi from 175 ksi for 2H.

From A194 2H vs 2HM nuts

How do I identify a 2HM nut?

By the marking stamped on one face: 2HM, plus the manufacturer’s identification mark. A 2H nut is marked 2H.

From A194 2H vs 2HM nuts

Which nut should be used with a B7 stud bolt?

An ASTM A194 Grade 2H heavy hex nut. Use 2HM with B7M in sour service, Grade 4 or 7 with L7 low-temperature studs, and 8 or 8M with B8 or B8M stainless studs.

From Hex and heavy hex nuts

What is the difference between 2H and 2HM nuts?

Both are heat-treated carbon steel heavy hex nuts, but 2HM is limited to 159–237 HB so it is safe in sour (H2S) service, while 2H runs from 24 to 38 HRC. 2HM has a lower proof stress of 150 ksi against 175 ksi for 2H.

From Hex and heavy hex nuts

What is a heavy hex nut?

A heavy hex nut is larger across flats and thicker than a standard hex nut of the same thread size, as defined in ASME B18.2.2. The extra size gives more bearing area and thread engagement, which is why it is the standard nut for flange stud bolts.

From Hex and heavy hex nuts

Do you supply metric nuts to ISO 4032 and DIN 934?

Yes, in property classes 8, 10 and 12 and in stainless A2 and A4, from M4 to M64.

From Hex and heavy hex nuts

Coatings, galvanizing and alloys

Why are galvanized nuts tapped oversize?

Hot-dip galvanizing adds a thick zinc layer to the bolt thread. To make the nut fit, it is tapped oversize after galvanizing, as allowed in ISO 10684 and ASTM A563. That is why galvanized bolts and nuts should always be bought as a matched set.

From Hot-dip galvanized bolts

How thick is a hot-dip galvanized coating on bolts?

ISO 10684 requires a mean coating thickness of at least 50 µm, with a local minimum of 40 µm. Electroplated zinc is much thinner, which is why HDG lasts far longer outdoors.

From Hot-dip galvanized bolts

Can class 10.9 bolts be hot-dip galvanized?

Class 10.9 can be galvanized with special precautions against hydrogen embrittlement, but zinc flake is often preferred. Class 12.9 and ASTM A490 bolts must not be hot-dip galvanized.

From Hot-dip galvanized bolts

What is the difference between galvanized and zinc plated bolts?

Galvanized bolts are dipped in molten zinc and get a thick coat for outdoor use. Zinc plated bolts are electroplated with a thin coat that suits indoor or sheltered use.

From Hot-dip galvanized bolts

Are hot-dip galvanized bolts suitable near the sea in Jubail or Dammam?

Yes, for structural steel and foundations. For seawater splash or immersion, stainless or duplex fasteners are better, and for process flanges that must be opened, PTFE coated studs are usually preferred.

From Hot-dip galvanized bolts

What is white rust on galvanized bolts?

White rust is zinc corrosion that forms when new galvanized bolts are stored wet or packed tight without ventilation. Store them dry and off the ground until use.

From Hot-dip galvanized bolts

When should I use super duplex bolting instead of B8M stainless?

When the bolts see warm seawater, brine or high chlorides. Type 316 (B8M) pits and can crack by chloride stress corrosion above about 60 °C, while super duplex S32750 and S32760 resist both and are roughly twice as strong.

From Duplex and nickel alloy fasteners

Is Inconel 718 suitable for sour service?

Yes, when it is supplied in the solution-annealed and aged condition within the hardness limits that NACE MR0175 / ISO 15156 sets for UNS N07718. State NACE on the enquiry and we will supply to those limits with the certificates to prove it.

From Duplex and nickel alloy fasteners

How do you prevent alloy mix-ups?

Every bar is identified by heat number from the mill certificate through machining, and we carry out positive material identification (PMI) on finished parts when the order requires it.

From Duplex and nickel alloy fasteners

Is PTFE coating better than galvanizing for stud bolts?

For process flange studs, usually yes: PTFE / Xylan coatings resist corrosion, do not need oversize nuts and make nuts easier to remove at the next turnaround. Galvanizing gives more sacrificial protection on structural bolts that will not be opened.

From Fastener coatings compared

Does Xylan coating affect torque?

Yes. Xylan and other PTFE coatings lower the nut factor to about 0.10, so torque must be reduced compared with plain oiled steel to avoid over-stressing the stud.

From Fastener coatings compared

What colour is Xylan coating?

Xylan is supplied in several colours, commonly blue, green or black; the colour is a project choice. Specify it with the coating system and thickness.

From Fastener coatings compared

Which coating is best for stud bolts in the Gulf?

For refinery and petrochemical flanges, Xylan / PTFE fluoropolymer over a zinc or phosphate base is the usual choice because it resists corrosion and makes disassembly easier. For structural and outdoor steel, hot-dip galvanizing gives the thickest sacrificial protection, and zinc flake is preferred on high-strength bolts that must not be electroplated.

From Coatings and finishes

Does a coating change the tightening torque?

Yes. Coatings change thread friction: PTFE coatings lower it, so the same torque gives much more preload than on plain steel, while galvanizing can raise it. Torque values must be set for the actual coating and lubricant. Our bolt torque calculator lets you change the nut factor to see the effect.

From Coatings and finishes

Can B7 stud bolts be hot-dip galvanized?

Yes. B7 studs are galvanized to ASTM F2329 or ISO 10684 and paired with 2H nuts tapped oversize to fit over the zinc thickness. We ship the studs and nuts together so the fit is right.

From Coatings and finishes

Do you apply coatings in-house?

Coatings are applied before dispatch through specialist coating partners we have worked with for years, each focused on one process. We check coating thickness and thread fit on the coated parts before release.

From Coatings and finishes

Bolts, screws and structural steel

Is DIN 912 the same as ISO 4762?

Yes for practical purposes. DIN 912 was replaced by ISO 4762, which has the same main dimensions. Most drawings still say DIN 912, and we supply to ISO 4762.

From Socket head cap screws

What is the difference between class 10.9 and 12.9 cap screws?

Class 12.9 has a minimum tensile strength of 1,220 MPa against 1,040 MPa for class 10.9, so it carries more load in the same size. 12.9 is standard for machine tools and tooling; 10.9 is common in general equipment.

From Socket head cap screws

Are stainless socket screws as strong as alloy steel?

No. A2-70 and A4-70 stainless screws have a minimum tensile strength of 700 MPa, and A4-80 has 800 MPa, compared with 1,220 MPa for class 12.9. Choose stainless for corrosion resistance, not strength.

From Socket head cap screws

Can class 12.9 screws be zinc plated?

They can, but electroplating high-strength screws risks hydrogen embrittlement, so they must be baked after plating. Zinc flake coating avoids that risk and is often preferred.

From Socket head cap screws

What hex key size fits an M12 cap screw?

A 10 mm hex key fits an ISO 4762 M12 cap screw. The table above lists key sizes from M4 to M36.

From Socket head cap screws

Do you supply inch socket head cap screws?

Yes. We supply ASTM A574 inch socket head cap screws to ASME B18.3 dimensions, in UNC and UNF threads.

From Socket head cap screws

What is the difference between A325 and A490 bolts?

Both are heavy hex structural bolts now covered by ASTM F3125. A325 has a minimum tensile strength of 120 ksi; A490 has 150 ksi with a maximum of 173 ksi. A490 allows smaller or fewer bolts but must not be hot-dip galvanized.

From Structural bolts

Which nut and washer go with A325 bolts?

An ASTM A563 Grade DH heavy hex nut (or A194 2H) and an ASTM F436 hardened washer. For galvanized A325 bolts, the nut must also be galvanized and tapped oversize.

From Structural bolts

Can A490 bolts be galvanized?

No. A490 bolts must not be hot-dip galvanized because of the risk of hydrogen embrittlement at their strength level. Where corrosion protection is needed, use an approved zinc flake coating or a different grade as the designer specifies.

From Structural bolts

Can pretensioned structural bolts be reused?

Under the RCSC Specification, A490 bolts and galvanized A325 bolts must not be reused once pretensioned. Plain A325 bolts may be retightened only if the engineer allows it.

From Structural bolts

What is the difference between EN 14399 HR and HV bolts?

HR sets (EN 14399-3) come in classes 8.8 and 10.9 with a longer thread and rely on the bolt yielding. HV sets (EN 14399-4) are class 10.9 only with a shorter thread and rely on the nut. Supply whichever system the project specification names; Saudi Aramco structural work under 12-SAMSS-007 uses ASTM A325 or A490 instead.

From Structural bolts

Do you supply direct tension indicators?

Yes. ASTM F959 direct tension indicators can be supplied with A325 and A490 bolt sets on request.

From Structural bolts

How do you measure a U-bolt?

Give four dimensions: rod diameter and thread, inside width between the legs, inside length from the inside of the bend to the end of the legs, and thread length. For pipe U-bolts, the pipe size (NPS) and pipe outside diameter are enough for us to size it.

From U-bolts

Which material should a pipe support U-bolt be?

Carbon steel class 4.6 or ASTM A307, hot-dip galvanized, covers most pipe racks. Use stainless A4 (316) or a polyolefin-coated U-bolt where the pipe is stainless or where galvanic corrosion is a concern.

From U-bolts

Do you supply U-bolts with nuts and plates?

Yes. U-bolts are supplied with two nuts as standard, and with washers or a cross plate when requested.

From U-bolts

Can any eye bolt be used for lifting?

No. Only forged lifting eye bolts with a stated working load limit and a test certificate should be used for lifting. Formed or bent-wire eye bolts are for tie-down and light fixing only.

From Eye bolts and eye nuts

What is the difference between shoulder and non-shoulder eye bolts?

A shoulder eye bolt has a collar that seats on the load surface, so it can take angular loads within the manufacturer’s derating. A plain non-shoulder eye bolt should only be loaded in line with its shank.

From Eye bolts and eye nuts

When should I use a swivel eye bolt?

When the load direction changes during the lift or the sling pulls at an angle, a swivel eye rotates and pivots to align with the load, which avoids bending the shank.

From Eye bolts and eye nuts

What is the difference between self-drilling and self-tapping screws?

A self-drilling screw has a drill point that cuts its own hole and thread in sheet steel in one operation. A self-tapping screw forms or cuts its thread but needs a pilot hole drilled first.

From Screws and rivets

Which socket screw grade should I order?

Class 12.9 for machinery where maximum strength is needed, class 8.8 or 10.9 for general equipment, and A2 or A4 stainless where corrosion matters more than strength.

From Screws and rivets

Can you make pins to a drawing?

Yes. Non-standard pins, shafts and plugs are turned and finished in our factory in Al-Jubail from carbon, alloy or stainless bar, with heat treatment arranged where the drawing requires it.

From Pins and plugs

What is a magnetic drain plug for?

A magnetic plug in a gearbox or engine sump collects steel wear particles from the oil, so they can be removed and inspected at each oil change.

From Pins and plugs

Can you cut sections to length?

Yes. Bars and sections are supplied cut to the lengths on your cutting list, and bar can be machined into finished parts to drawing.

From Structural steel and bars

What is the difference between a hex bolt and a heavy hex bolt?

A heavy hex bolt has a larger and thicker head for the same diameter, which spreads load over a bigger bearing area. Heavy hex bolts to ASME B18.2.1 and ASTM A325 / F3125 are used in structural steel connections; standard hex bolts to ISO 4014 and ISO 4017 cover general engineering.

From Hex and heavy hex bolts

Is DIN 933 the same as ISO 4017?

Almost. DIN 931 and DIN 933 were withdrawn and replaced by ISO 4014 and ISO 4017, which use the same thread and length rules but a smaller hexagon on four sizes: M10 is 16 mm across flats (17 mm in DIN), M12 is 18 mm (19), M14 is 21 mm (22) and M22 is 34 mm (32). Tell us which one your drawing calls for so the spanner size matches.

From Hex and heavy hex bolts

What is the difference between class 8.8 and 10.9 bolts?

Class 8.8 bolts have a minimum tensile strength of 800 MPa (830 MPa above M16) and class 10.9 bolts 1040 MPa, both to ISO 898-1. The first number is the tensile strength in hundreds of MPa and the decimal is the ratio of proof strength to tensile strength.

From Hex and heavy hex bolts

Can high-strength bolts be galvanized?

Class 8.8 and A325 bolts are routinely hot-dip galvanized with oversized-tapped nuts. For class 10.9 and above, zinc flake is usually preferred because electroplating and some galvanizing processes raise the risk of hydrogen embrittlement. We follow your specification and advise when a coating does not suit the grade.

From Hex and heavy hex bolts

Which washer goes with a structural or B7 bolt?

An ASTM F436 through-hardened washer, which is harder (26 to 45 HRC) than the bolt and nut so it does not dish or gall under tightening. Metric structural joints use hardened ISO 7089 300 HV or equivalent washers.

From Washers

What is a DTI washer?

A direct tension indicator (DTI) is a hardened washer with protrusions that flatten as the bolt reaches its specified tension, so an inspector can check tension with a feeler gauge instead of a torque wrench. DTIs are made to ASTM F959.

From Washers

Do spring lock washers stop bolts loosening?

Split spring washers to DIN 127 give some resistance in light-duty joints, but they do not reliably prevent loosening under heavy vibration. For critical joints, correct preload, wedge-locking washers or prevailing-torque nuts work better.

From Washers

Anchor bolts, anchors and threaded rod

What is the difference between expansion and chemical anchors?

Expansion anchors hold by pressing a sleeve or clip against the sides of the drilled hole when tightened. Chemical anchors hold by bonding a threaded rod into the hole with resin. Chemical anchors usually allow higher loads and closer edge distances but need clean holes and curing time.

From Expansion and chemical anchors

What does cracked concrete mean for anchors?

Concrete in tension zones of beams and slabs can develop small cracks under load. Anchors approved for cracked concrete keep their capacity when a crack passes through the hole; others may lose holding power. The design decides whether a cracked-concrete approval is needed.

From Expansion and chemical anchors

Can you supply threaded rods for chemical anchoring?

Yes. We cut class 5.8, 8.8 or A4-70 stainless threaded rod to the embedment length you need, grind a chisel point and supply each stud with a nut and washer, zinc plated or hot-dip galvanized.

From Expansion and chemical anchors

Does hot weather affect chemical anchors?

Yes. In Gulf summer heat the resin gels and cures faster, so working time is shorter. Store cartridges cool, follow the manufacturer’s temperature table and do not load the anchor before full cure.

From Expansion and chemical anchors

Which anchors should be used near the coast?

In coastal areas such as Jubail, Dammam and Ras Tanura, use A4 (316) stainless anchors for exposed fixings, or hot-dip galvanized anchors where the design allows. Zinc-plated anchors are for dry indoor use only.

From Expansion and chemical anchors

Do you supply approved anchor systems?

Yes. Where the design specifies an anchor with an ETA or ICC-ES approval, we quote that system or an approved equivalent accepted by the engineer, with the approval document.

From Expansion and chemical anchors

What is the difference between a threaded rod and a stud bolt?

A threaded rod is supplied as a long bar threaded end to end. A stud bolt is a piece cut from rod (or made individually) to a set length, usually with chamfered ends and two nuts. We supply both, and cut stud bolts from B7 rod to your flange list.

From Threaded rods

Is DIN 975 still valid?

DIN 975 was withdrawn and replaced by DIN 976-1, which covers the same threaded rods. Most enquiries still say DIN 975; we supply to DIN 976-1 dimensions and property classes from ISO 898-1.

From Threaded rods

Can you cut threaded rod to length?

Yes. We cut rods to your length list, chamfer the ends and fit nuts and washers if required. Lengths are checked and tagged before dispatch.

From Threaded rods

Which threaded rod should I use for chemical anchors?

Usually class 8.8 zinc-plated or hot-dip galvanized rod, or A4-70 stainless near the coast, in the diameter and embedment set by the anchor approval. We can supply the rods with a chisel point, nut and washer.

From Threaded rods

Which nut goes with B7 threaded rod?

An ASTM A194 grade 2H heavy hex nut. For class 8.8 metric rod, a class 8 nut to ISO 4032 or DIN 934.

From Threaded rods

Can threaded rods be hot-dip galvanized?

Yes, up to class 8.8 and B7. The nuts must then be tapped oversize to fit over the zinc on the rod thread.

From Threaded rods

What is an anchor bolt?

An anchor bolt is a bolt cast into concrete, or fixed into drilled concrete, to hold steel columns, equipment skids, tanks and pipe supports to their foundations. Cast-in anchor bolts are usually specified to ASTM F1554 in the US system or ISO 898-1 / EN 10025 steels in the metric system.

From Anchor bolts

What do the F1554 colour codes mean?

The colour painted on the end of an ASTM F1554 anchor bolt shows its grade: blue for Grade 36, yellow for Grade 55 and red for Grade 105. The marking is required unless the grade is stamped on the bolt instead.

From Anchor bolts

Which nuts and washers go with F1554 anchor bolts?

ASTM A563 Grade A nuts for Grades 36 and 55, and A563 DH or A194 2H heavy hex nuts for Grade 105, with ASTM F436 hardened washers. Galvanized bolts take nuts tapped oversize for the coating.

From Anchor bolts

Can you supply anchor bolts in sets with templates?

Yes. We supply anchor bolts with nuts, washers and plate washers as sets, and can fabricate setting templates to your foundation drawing so the bolt pattern is held during the pour.

From Anchor bolts

Flanges and gaskets

Can you supply flanges with stud bolts and gaskets?

Yes. Tell us the NPS, pressure class, facing and material, and we supply the flange pair with the correct number and size of stud bolts, nuts and a matching gasket for each joint.

From Flanges

Which flange material is used for low-temperature service?

ASTM A350 LF2 carbon steel flanges are impact tested for low-temperature service, usually paired with A320 L7 stud bolts and A194 Grade 7 nuts.

From Flanges

Which gasket is standard for raised face process flanges?

A spiral wound gasket to ASME B16.20, usually 316L windings with flexible graphite filler, an inner ring and a carbon steel outer centering ring. The colour coding on the outer ring identifies winding and filler materials.

From Gaskets and rings

When is a ring type joint gasket used?

RTJ gaskets are used on ring type joint flanges in high-pressure and high-temperature service, typically Class 900 and above and in wellhead equipment. The ring material must be softer than the flange groove.

From Gaskets and rings

Standards, certificates and technical data

How much does a 1″ × 6″ stud bolt weigh?

About 0.51 kg in carbon or alloy steel, and about 0.87 kg with two heavy hex nuts.

From Bolt weight calculator for stud bolts and nuts

How much does a 1″ heavy hex nut weigh?

About 0.18 kg in steel, by ASME B18.2.2 dimensions.

From Bolt weight calculator for stud bolts and nuts

How much does an M20 stud bolt weigh?

An M20 × 150 mm stud weighs about 0.31 kg in carbon steel; an M20 heavy hex nut adds about 0.10 kg.

From Bolt weight calculator for stud bolts and nuts

Why use pitch diameter instead of nominal diameter?

Threads remove metal, so a threaded stud weighs less than a plain bar of the same nominal size. The pitch diameter gives a closer estimate.

From Bolt weight calculator for stud bolts and nuts

Is the calculator accurate enough for invoicing?

No. It is an estimate for freight, packing and lifting plans, within about 5%. Invoices use actual weighed or counted quantities.

From Bolt weight calculator for stud bolts and nuts

What is 22 HRC in Brinell?

About 237 HB (and 248 HV) on the ASTM E140 conversion for steel. It is the NACE MR0175 / ISO 15156 limit for sour-service carbon and low-alloy steel.

From Steel hardness conversion chart: HRC, HB, HV

What is 35 HRC in Brinell?

About 327 HB on the ASTM E140 table. ASTM A193 B7 studs are limited to 35 HRC (321 HB).

From Steel hardness conversion chart: HRC, HB, HV

Are hardness conversions exact?

No. ASTM E140 conversions are approximate and depend on the material. Acceptance should be based on the scale and method the specification names.

From Steel hardness conversion chart: HRC, HB, HV

Can I convert hardness to tensile strength?

Only approximately, for carbon and low-alloy steel. Use the conversion as a check, not as a substitute for a tensile test.

From Steel hardness conversion chart: HRC, HB, HV

Do these conversions work for stainless steel?

Not for austenitic stainless steel such as 304 and 316 (B8 and B8M), which needs its own conversion tables.

From Steel hardness conversion chart: HRC, HB, HV

What thread do stud bolts use?

Under ASME B16.5, flange stud bolts use UNC threads up to 1″ diameter and the 8-thread series (8UN) for larger diameters. ASTM A193 bolting follows the same rule.

From Thread pitch chart: UNC, UNF, 8UN and metric

What does 8UN mean?

A constant pitch series with 8 threads per inch, used for stud bolts above 1″ diameter regardless of size.

From Thread pitch chart: UNC, UNF, 8UN and metric

How many threads per inch does a 3/4″ bolt have?

10 TPI for UNC (coarse) and 16 TPI for UNF (fine).

From Thread pitch chart: UNC, UNF, 8UN and metric

What is the pitch of an M20 bolt?

2.5 mm for coarse thread; the common fine pitch is 1.5 mm, written M20 × 1.5.

From Thread pitch chart: UNC, UNF, 8UN and metric

Can metric and inch nuts be mixed?

No. Even where sizes are close, such as 1/2″ and M12, the pitch and thread form differ and the nut will not engage correctly.

From Thread pitch chart: UNC, UNF, 8UN and metric

What target stress should I use for B7 flange bolting?

Many bolted-joint procedures target between 40% and 70% of the bolt yield strength, with 50% a common starting point for B7 on standard flanges. The right value depends on the gasket and flange, so use the figure in your joint procedure or ASME PCC-1 assessment.

From Bolt torque calculator

Why does PTFE coating reduce torque?

PTFE lowers friction in the threads and under the nut, so the nut factor K drops to around 0.10. Less torque is lost to friction, so less torque is needed to reach the same preload.

From Bolt torque calculator

Is torque an accurate way to set preload?

Torque is the most common method but preload can scatter by around ±25% or more because friction varies. Hydraulic tensioning, load-indicating washers or ultrasonic measurement give tighter control on critical joints.

From Bolt torque calculator

What do three lines on a bolt head mean?

Three radial lines mark an SAE J429 Grade 5 bolt, a medium-carbon quenched and tempered bolt with 120 ksi minimum tensile strength up to 1 inch. Six lines mark Grade 8.

From Fastener grade markings and strength

What does 8.8 on a bolt mean?

It marks ISO 898-1 property class 8.8: 800 MPa minimum tensile strength (830 MPa above M16) and a yield strength of 80% of that.

From Fastener grade markings and strength

Where is the grade marked on a stud bolt?

On one end of the stud, together with the manufacturer’s mark. Heavy hex nuts are marked on one face.

From Fastener grade markings and strength

Do you supply to standards not listed here?

Often, yes. Send the standard or the project specification with your enquiry and we will confirm.

From Standards and grades reference

Is DIN 933 still a valid standard?

DIN 931 and DIN 933 were withdrawn and replaced by ISO 4014 and ISO 4017, but many drawings still quote them. We can supply to either and will point out the across-flats differences on M10, M12, M14 and M22.

From Standards and grades reference

Is a mill test report the same as a 3.1 certificate?

A mill test report is usually the steel mill’s 3.1 certificate for the bar. A fastener 3.1 certificate covers the finished bolts or studs, linking the bar heat to the heat-treated, tested product.

From EN 10204 3.1 vs 3.2 certificates

Who can sign a 3.2 certificate?

The manufacturer’s authorised inspection representative together with the purchaser’s authorised representative or an inspector designated by official regulations, such as a third-party inspection agency.

From EN 10204 3.1 vs 3.2 certificates

Does every fastener order need a certificate?

For pressure, structural and lifting applications, yes. JTE Fasteners supplies a 3.1 certificate with every order as standard.

From EN 10204 3.1 vs 3.2 certificates

Is JTE Fasteners ISO 9001 certified?

Yes. JTE Fasteners operates an ISO 9001-certified quality management system covering the manufacture and supply of fasteners. We send the certificate with registrar details to buyers on request.

From Quality and certificates

Are you registered with Saudi Aramco and SABIC?

Yes. JTE Fasteners is a registered vendor with Saudi Aramco and SABIC. Vendor details are shared with procurement teams on request.

From Quality and certificates

Can our inspector witness tests?

Yes. We accommodate your nominated third-party inspection agency for EN 10204 3.2 certification, at our Jubail facility or at the test laboratory.

From Quality and certificates

Ordering and supply in Saudi Arabia

Where is JTE Fasteners located?

In Al Dana District, Al Jubail, Eastern Province, on King Fahd Ibn Abdulaziz Road (Plot SC/004, Lot 00193, postal code 35514).

From JTE Fasteners & Hardwares company profile

When was JTE Fasteners founded?

In 2014, growing out of M/S. Neel Al-Khair Metal Factory (formerly Neel Al Khair Lathe for Metals), a machining business that served Eastern Province industry before that.

From JTE Fasteners & Hardwares company profile

What is JTE Fasteners’ legal name?

Jarallah Bin Nasser Bin Shaflout Al-Qahtani Trading Establishment. The trading brand is JTE Fasteners & Hardwares.

From JTE Fasteners & Hardwares company profile

What approvals does JTE hold?

JTE is ISO 9001 certified and a registered Saudi Aramco and SABIC vendor, and issues EN 10204 3.1 certificates with every order.

From JTE Fasteners & Hardwares company profile

What does JTE manufacture?

Stud bolts, threaded rod and special fasteners in its factory in Al-Jubail, and it supplies bolts, nuts, washers, anchor bolts, flanges, gaskets and structural steel alongside them.

From JTE Fasteners & Hardwares company profile

How do I request vendor registration documents?

Email [email protected] or use the quote form, and list what you need: ISO 9001 certificate, commercial registration, VAT certificate, vendor registration details and a sample 3.1 certificate.

From JTE Fasteners & Hardwares company profile

What approvals should a fastener supplier in Saudi Arabia have?

At minimum ISO 9001, registration with the owner whose plant the bolts are going into, such as Saudi Aramco, SABIC or the main contractor, and the ability to issue EN 10204 3.1 certificates that trace to the lot.

From How to choose a fastener supplier in Saudi Arabia

Is ISO 9001 enough for Saudi Aramco projects?

No. ISO 9001 proves a quality system, but buying for Aramco plants also needs vendor registration and material that meets Aramco specifications such as SAES-L-109 and the purchase order.

From How to choose a fastener supplier in Saudi Arabia

What is the difference between a 3.1 and a 3.2 certificate?

A 3.1 certificate is issued by the maker’s independent inspection department; a 3.2 is also signed by the buyer’s representative or a third-party inspector. See 3.1 vs 3.2 explained.

From How to choose a fastener supplier in Saudi Arabia

Can imported fasteners be used on Saudi Aramco projects?

Yes, if they meet the specification and come from a source the purchase order accepts, with the required certificates and SASO requirements where they apply.

From How to choose a fastener supplier in Saudi Arabia

How do I check a stud bolt’s grade?

From the marks on the stud end and the nut (see fastener grade markings) and from the certificate that traces to the heat.

From How to choose a fastener supplier in Saudi Arabia

What should a supplier’s quotation include?

Grade and nut, size and length, coating and its specification, certificate level, lead time and delivery terms.

From How to choose a fastener supplier in Saudi Arabia

Who supplies stud bolts in Saudi Arabia?

Saudi Arabia has several local fastener manufacturers and stockists, most of them in the Eastern Province close to the plants. JTE Fasteners is one of them: a manufacturer and supplier in Al Jubail since 2014, ISO 9001 certified, a registered Saudi Aramco and SABIC vendor, and machining stud bolts in its own factory.

From Fasteners and stud bolts supplier in Saudi Arabia

Is JTE Fasteners a Saudi Aramco approved vendor?

Yes. JTE is a registered vendor with Saudi Aramco and SABIC and is ISO 9001 certified. Ask for the vendor registration details with your RFQ if your purchasing team needs them.

From Fasteners and stud bolts supplier in Saudi Arabia

Do you supply outside the Eastern Province?

Yes. We supply from our factory in Al-Jubail to the Eastern Province, Riyadh and the rest of the Kingdom. Delivery terms and time are stated on each quotation.

From Fasteners and stud bolts supplier in Saudi Arabia

Which standards do you work to?

ASTM, ASME, ISO, DIN and EN, plus the Saudi owners’ requirements: Saudi Aramco SAES-L-109, 12-SAMSS-007 and 09-SAMSS-107, SABIC material specifications, and the Saudi Building Code (SBC 304 and SBC 306) for building work.

From Fasteners and stud bolts supplier in Saudi Arabia

Can you make non-standard fasteners?

Yes. Stud bolts, threaded rod and special fasteners are cut and threaded in our factory in Al-Jubail from certified material, including odd lengths and parts copied from a sample.

From Fasteners and stud bolts supplier in Saudi Arabia

What certificates come with an order?

EN 10204 3.1 certificates traceable to heat number with every order; 3.2 with third-party inspection when requested; hardness and PMI reports where the specification asks for them.

From Fasteners and stud bolts supplier in Saudi Arabia

Can you prepare shutdown bolting kits?

Yes. We kit studs, nuts and gaskets flange by flange, marked and certified. See shutdown bolting kits.

From Fasteners and stud bolts supplier in Saudi Arabia

Can I deal with you in Arabic?

Yes. Our team handles quotations, documents and follow-up in Arabic and English.

From Fasteners and stud bolts supplier in Saudi Arabia

Do you supply fasteners to Riyadh?

Yes. JTE Fasteners supplies anchor bolts, structural and hex bolts, stud bolts, nuts, washers and custom fasteners to Riyadh from its factory in Al-Jubail, delivered by road with EN 10204 3.1 certificates.

From Fasteners supplier in Riyadh

How far is JTE Fasteners from Riyadh?

Our factory is in Al Dana District, Al Jubail, about 450 km from Riyadh, roughly four and a half hours by road. We confirm the dispatch date with each quote.

From Fasteners supplier in Riyadh

Can you make anchor bolts to length for a Riyadh project?

Yes. ASTM F1554 grade 36, 55 and 105 anchor rods are made to the length, thread length and shape on your drawing, plain or hot-dip galvanized, with heavy hex nuts and plate washers.

From Fasteners supplier in Riyadh

Do bolts in Riyadh need hot-dip galvanizing?

Not always. Riyadh’s dry climate is less corrosive than the coast, so sheltered and indoor bolting can be plain or zinc plated. Permanent outdoor steelwork and foundations are usually hot-dip galvanized, with oversize-tapped nuts.

From Fasteners supplier in Riyadh

Do you deliver to Sudair Industrial City and Al Kharj?

Yes. We deliver to the Riyadh Second Industrial City, Sudair Industrial City, Al Kharj and project sites across the Riyadh region.

From Fasteners supplier in Riyadh

Do your bolts come with certificates?

Yes. Every order includes an EN 10204 3.1 mill test certificate traceable to heat number. Your third-party inspector can witness tests at our factory in Al-Jubail for 3.2 release.

From Fasteners supplier in Riyadh

Who supplies stud bolts for Ras Tanura?

JTE Fasteners supplies stud bolts, heavy hex nuts, turnaround bolting kits, coated studs, gaskets and anchor bolts to Ras Tanura, Ju’aymah, Qatif and Safwa from its factory in Al-Jubail. We are a registered Saudi Aramco and SABIC vendor and ISO 9001 certified.

From Fasteners supplier in Ras Tanura

How far is JTE Fasteners from Ras Tanura?

Our factory is in Al Dana District, Al Jubail, about 70 km from Ras Tanura by road. The drive takes under an hour.

From Fasteners supplier in Ras Tanura

Can you build turnaround bolting kits for Ras Tanura?

Yes. Send the joint or line list with flange sizes, classes and service. We supply studs, nuts and gaskets bagged and tagged by joint, with agreed spares, and machine any non-standard pieces in Jubail.

From Fasteners supplier in Ras Tanura

Which stud bolts are used for high-temperature refinery service?

Above about 450 °C, ASTM A193 B16 studs with A194 grade 4 or 7 nuts are commonly specified, because B7 loses preload through relaxation at those temperatures.

From Fasteners supplier in Ras Tanura

Which bolts are used for LPG and NGL refrigerated service?

ASTM A320 L7 studs with A194 grade 7 nuts, which are impact tested to stay tough at low temperatures.

From Fasteners supplier in Ras Tanura

Do you supply sour-service bolting to NACE MR0175?

Yes. ASTM A193 B7M studs with A194 2HM nuts, hardness controlled to NACE MR0175 / ISO 15156 limits.

From Fasteners supplier in Ras Tanura

Is there a fastener supplier near Ras Al Khair?

Yes. JTE Fasteners is in Al Jubail, about 100 km south of Ras Al Khair Industrial City, and supplies stud bolts, nuts, anchor bolts, structural bolts and corrosion-resistant fasteners to plants, contractors and yards there.

From Fasteners supplier in Ras Al Khair

How far is JTE Fasteners from Ras Al Khair?

Our factory is at Plot SC/004, Al Dana District, Al Jubail, about 100 km south of Ras Al Khair along the Gulf coast.

From Fasteners supplier in Ras Al Khair

Which bolts should be used for seawater and desalination service?

Seawater intake and reverse osmosis high-pressure lines usually use duplex or super duplex fasteners, because they resist chloride pitting better than 316 stainless. Hot brine service may need super duplex or nickel alloys, as set by the plant specification.

From Fasteners supplier in Ras Al Khair

What bolting is used for cold ammonia service?

Low-temperature lines and refrigerated ammonia storage use ASTM A320 L7 studs with A194 grade 7 nuts, which are impact tested to stay tough at low temperature.

From Fasteners supplier in Ras Al Khair

Are galvanized bolts suitable for acid plants?

No. Zinc coatings dissolve quickly in acid. In sulphuric and phosphoric acid areas we recommend PTFE-coated B7 bolting or B8M class 2 stainless where spills can reach the bolts.

From Fasteners supplier in Ras Al Khair

Can you supply shutdown bolting kits for Ras Al Khair plants?

Yes. We build kits by joint with studs, nuts and gaskets tagged to your line list, and machine any non-standard pieces in Jubail.

From Fasteners supplier in Ras Al Khair

Who supplies stud bolts in Al Khobar?

JTE Fasteners supplies stud bolts, heavy hex nuts, anchor bolts, coated bolting and shutdown kits to Al Khobar and Dhahran from its factory in Al-Jubail. We are ISO 9001 certified, a registered Saudi Aramco and SABIC vendor, and include an EN 10204 3.1 certificate with every order.

From Fasteners supplier in Al Khobar

How far is JTE Fasteners from Al Khobar?

Our factory is in Al Dana District, Al Jubail, about 110 km north of Al Khobar. The drive takes roughly an hour and ten minutes.

From Fasteners supplier in Al Khobar

Can you quote from a material requisition or line list?

Yes. Send the requisition with the specification. We check grades, coatings and stud lengths against it and quote line by line, flagging anything that conflicts.

From Fasteners supplier in Al Khobar

Do you supply NACE MR0175 sour-service bolting?

Yes. For sour service we supply ASTM A193 B7M studs with A194 2HM nuts, which are hardness controlled to meet NACE MR0175 / ISO 15156 limits.

From Fasteners supplier in Al Khobar

Can my inspector witness testing before delivery to Khobar?

Yes. Your third-party inspector can witness tests at our factory in Al-Jubail, and we issue documentation for EN 10204 3.2 release.

From Fasteners supplier in Al Khobar

Do you deliver to Dhahran?

Yes. We deliver across Dhahran and Al Khobar. For sites that need gate passes, send the access details with the order so delivery can be arranged.

From Fasteners supplier in Al Khobar

Can you supply customers in Bahrain?

Yes. Certified bolting can be shipped from Jubail to Bahrain by road over the King Fahd Causeway. Tell us the delivery address and the documents customs will need.

From Fasteners supplier in Al Khobar

Who supplies stud bolts and fasteners in Dammam?

JTE Fasteners supplies stud bolts, heavy hex bolts and nuts, anchor bolts, washers, flanges and gaskets to Dammam from its base in Al Jubail. We are ISO 9001 certified, a registered Saudi Aramco and SABIC vendor, and ship every order with an EN 10204 3.1 certificate.

From Fasteners supplier in Dammam

How far is JTE Fasteners from Dammam?

Our factory is at Plot SC/004, Al Dana District, Al Jubail, about 90 km north of Dammam on the Dhahran–Jubail Highway. The drive takes roughly one hour.

From Fasteners supplier in Dammam

Do you deliver to the Second Industrial City in Dammam?

Yes. We deliver to the First and Second Industrial Cities, King Abdulaziz Port and sites across Greater Dammam. Send the plot or gate details with your order so the driver can get access.

From Fasteners supplier in Dammam

Can I get an EN 10204 3.1 certificate for bolts delivered to Dammam?

Yes. Every order comes with an EN 10204 3.1 mill test certificate traceable to heat number. If your project needs 3.2, your third-party inspector can witness tests at our factory in Al-Jubail.

From Fasteners supplier in Dammam

Which bolts resist corrosion best near the coast in Dammam?

For flanges that must come apart, PTFE-coated B7 studs with 2H nuts. For permanent outdoor steel and anchor bolts, hot-dip galvanized bolts with oversize-tapped nuts. For seawater or brine service, stainless B8M or duplex fasteners.

From Fasteners supplier in Dammam

Can you make non-standard bolts for a Dammam plant?

Yes. Odd lengths, special threads and obsolete sizes are machined to your drawing or sample in our factory in Al-Jubail, in the grade your specification requires.

From Fasteners supplier in Dammam

Do you supply bolting to Saudi Aramco and SABIC specifications in Dammam?

Yes. We are a registered Saudi Aramco and SABIC vendor and supply bolting to the material, coating and documentation requirements of the project specification.

From Fasteners supplier in Dammam

What is in a shutdown bolting kit?

For each flange joint: the stud bolts cut to the right length for the gasket being fitted, two nuts per stud, washers if specified and the gasket, packed together and tagged with the joint or line number.

From Shutdown bolting kits

Can kits include spares?

Yes. We add the spare allowance you specify, usually a percentage per size, packed separately so it is easy to find on site.

From Shutdown bolting kits

How early should we order for a turnaround?

As early as the joint list is fixed. Standard B7 and 2H bolting is quick; coated, alloy and NACE items take longer, so send those lines first.

From Shutdown bolting kits

Which stud bolts are used for sour service?

ASTM A193 B7M studs with ASTM A194 2HM nuts. Both are hardness-limited so they meet NACE MR0175 / ISO 15156 for sulfide stress cracking, and every B7M stud is hardness tested. For low-temperature sour service, A320 L7M with A194 7M nuts.

From Oil and gas

Can you supply bolting to Saudi Aramco specifications?

Yes. We are a registered Saudi Aramco vendor and supply bolting to the material, coating and documentation requirements stated in the purchase order and the referenced specifications.

From Oil and gas

Do you supply PTFE-coated bolting for offshore and coastal plants?

Yes, studs and nuts coated with Xylan 1070 or 1424 fluoropolymer, with coating thickness reports on request.

From Oil and gas

When should B16 replace B7?

When the bolt metal temperature runs above about 450 °C (840 °F). B16 is a chromium-molybdenum-vanadium steel that keeps its strength and resists creep relaxation at higher temperatures than B7.

From Petrochemical and refining

Do you make tap-end studs for heat exchangers?

Yes. Tap-end and reduced-body studs are machined to drawing in Jubail in B7, B16 and stainless grades.

From Petrochemical and refining

Why not use 316 stainless bolts in seawater?

Type 316 (B8M) suffers pitting and crevice corrosion in warm seawater and can crack by chloride stress corrosion above about 60 °C. Super duplex and 6Mo alloys resist both and are stronger.

From Power and desalination

Do you supply insulation for dissimilar-metal joints?

Yes. We can supply insulating washers and sleeves with the bolting where your design calls for galvanic isolation.

From Power and desalination

Which anchor bolt grade is used for steel columns?

ASTM F1554 Grade 36 is the usual choice for column bases; Grade 55 or 105 is used where design uplift or moment is higher. In metric designs, class 8.8 or S355JR anchors are common.

From Construction and steel structures

How do you check structural bolt tension on site?

Direct tension indicator (DTI) washers to ASTM F959 flatten when the bolt reaches its specified tension, so an inspector can check each bolt with a feeler gauge.

From Construction and steel structures

What is the best coating for bolts in the splash zone?

A duplex system, either hot-dip galvanizing or zinc flake under a fluoropolymer topcoat, gives the longest life on carbon steel bolts in the splash zone. For immersed joints, switch to a corrosion-resistant alloy such as super duplex.

From Marine and offshore

Can stainless bolts be used on galvanized marine structures?

They can, but stainless and zinc form a galvanic couple that consumes the zinc around the bolt. Insulating washers and sleeves, or galvanized bolts on galvanized steel, avoid it.

From Marine and offshore

Do you manufacture fasteners or only trade them?

Both. We machine and thread fasteners in-house in Jubail, a capability that comes from M/S. Neel Al-Khair Metal Factory, and we supply standard items from stock. Non-standard lengths, threads and drawing-specific parts are made to order.

From Home

Which certificate comes with an order?

Every order ships with an EN 10204 3.1 material test certificate that traces each item to its heat number. EN 10204 3.2 certificates with your nominated third-party inspector are available on request.

From Home

Are you an approved vendor for Saudi Aramco and SABIC?

Yes. JTE Fasteners is a registered vendor with Saudi Aramco and SABIC and operates an ISO 9001-certified quality management system. We share registration details and certificates with buyers on request.

From Home

Can you supply PTFE or Xylan coated stud bolts?

Yes. We supply stud bolts and nuts coated with Xylan 1070 or 1424 PTFE, hot-dip galvanizing, zinc flake, zinc-nickel or zinc plating, applied before dispatch through our specialist coating partners. Tell us the coating specification and thickness on the enquiry.

From Home

What do you need to quote quickly?

Product, standard and grade, diameter and length, coating, quantity and the certificate you need. A bill of materials or project specification in PDF or Excel works just as well.

From Home

What can you machine to drawing?

Stud bolts and bolts in non-standard diameters, lengths and thread lengths, tap-end and reduced-body studs, special nuts, pins, bushes, shafts and small machined parts, in carbon, alloy, stainless and duplex bar.

From Custom manufacturing

Can you match an old or damaged bolt with no drawing?

Usually yes. Send a sample or photos with measurements, the material if known and the service conditions; we will measure it, propose a grade and confirm before making.

From Custom manufacturing

How are custom parts certified?

Each part is traced to the bar heat number on the mill certificate, inspected for dimensions and thread fit with gauges, marked as the specification requires, and supplied with an EN 10204 3.1 certificate.

From Custom manufacturing

What should I include in a quotation request?

Product, standard and grade, diameter and length, coating, quantity, delivery location and the certificate you need. Attach your BOM, drawing or specification if you have one.

From Contact

Can I send my enquiry on WhatsApp?

Yes. Send it to +966 54 614 8678, including photos of a sample part if you are matching an existing bolt.

From Contact

Is there a stud bolt and fastener supplier in Jubail Industrial City?

Yes. JTE Fasteners is based in Al Jubail at Plot SC/004, Al Dana District, King Fahd Ibn Abdulaziz Road, and supplies stud bolts, heavy hex bolts and nuts, anchor bolts, flanges, gaskets and coated bolting to plants, contractors and fabricators in Jubail Industrial City and Jubail 2.

From Fasteners supplier in Jubail

Do you manufacture bolts in Jubail or only trade them?

Both. We stock standard items and machine studs to length, special threads, anchor bolts and obsolete sizes to drawing or sample in our own factory in Al-Jubail.

From Fasteners supplier in Jubail

Do you supply bolting to Saudi Aramco and SABIC specifications?

Yes. We are a registered Saudi Aramco and SABIC vendor and supply bolting to the material, coating, marking and documentation requirements of the plant or project specification.

From Fasteners supplier in Jubail

Which certificate comes with the bolts?

Every order includes an EN 10204 3.1 mill test certificate traceable to heat number. If your project needs 3.2, your third-party inspector can witness tests at our factory in Al-Jubail.

From Fasteners supplier in Jubail

Can you help with an urgent breakdown in Jubail?

Yes. Call or WhatsApp +966 54 614 8678 with a photo, the size, grade, length and quantity. Standard items can come from stock, and odd sizes can be machined in our factory.

From Fasteners supplier in Jubail

Do you build shutdown bolting kits?

Yes. Send the joint or line list with flange sizes, classes and service. We supply studs, nuts and gaskets bagged and tagged by joint, with agreed spares.

From Fasteners supplier in Jubail

Which stud bolts are used for sour service in Jubail plants?

ASTM A193 B7M studs with A194 2HM nuts, hardness controlled to meet NACE MR0175 / ISO 15156.

From Fasteners supplier in Jubail

Which bolts are used for cold and cryogenic service?

Down to about −101 °C, ASTM A320 L7 studs with A194 grade 7 nuts. Below that, A320 B8 or B8M class 1 stainless studs with grade 8 or 8M nuts.

From Fasteners supplier in Jubail

Can I collect from your premises?

Yes, by arrangement. Call before you come so the order is ready and the certificates are printed.

From Fasteners supplier in Jubail

Do you deliver outside Jubail?

Yes. We deliver to Ras Al Khair, Dammam, Al Khobar, Dhahran, Ras Tanura and Qatif, and ship to Riyadh and the rest of Saudi Arabia.

From Fasteners supplier in Jubail

What fasteners does JTE Fasteners supply?

Stud bolts, hex and heavy hex bolts, hex and heavy hex nuts, anchor bolts, U-bolts, eye bolts and eye nuts, washers, screws and rivets, pins and plugs, plus flanges, gaskets and structural steel bars. Each is available in carbon steel, alloy steel, stainless steel, duplex and nickel alloys, plain or coated.

From Products

Which standards do you manufacture and supply to?

ASTM (A193, A194, A320, A453, A307, A325, A563, F1554, F436), ASME B18.2.1, B18.2.2, B1.1 and B16.5, ISO 898-1, ISO 898-2, ISO 3506 and ISO 4014/4017/4032, DIN 931, 933, 934, 125 and 127, BS 4190 and EN 10025, and Shell MESC SPE 81 series. If your project uses a different specification, send it with the enquiry.

From Products

Can you make non-standard sizes?

Yes. Non-standard diameters, lengths, thread lengths, reduced-body studs, tap-end studs and drawing-specific parts are machined and threaded to order in our factory in Al-Jubail.

From Products

What size range do you cover?

Bolts, studs and nuts from M4 to M64 in metric and from 1/4 inch to 4 inches in imperial sizes, with UNC and 8UN threads for inch studs. Anchor bolts run from M6 to M50.

From Products

Updated

Related

Technical library

Guides, charts and calculators.

Nut compatibility chart

Which nut goes with which bolt.

Fasteners supplier in Saudi Arabia

Where we supply and the requirements we work to.

Question not answered here?

Send it with your drawing or specification and we will reply.

Request a quote+966 54 614 8678