+966 54 614 8678 [email protected] WhatsApp
JTE FastenersBolting & hardware, Al Jubail العربية Request a quote

Zinc flake coated bolts, nuts and studs

High-strength bolts, nuts and studs with a zinc flake coating to ISO 10683 or ASTM F3393, applied by specialist coaters and supplied from Al Jubail, for corrosion protection where hot-dip galvanizing is too thick or not allowed.

Zinc flake is a thin coating of zinc and aluminium flakes in a binder, applied by dip-spin or spray and then cured, with no electric current; parts are normally cleaned by alkaline degreasing or shot blasting rather than acid pickling. Because the process makes no hydrogen, it is widely used on high-strength fasteners of 1000 MPa and above, such as 10.9 and 12.9 bolts. The film is typically 8 to 20 µm, against about 50 µm for hot-dip galvanizing, so standard thread tolerances can normally be kept.

Standards
ISO 10683:2018; ASTM F3393 (replaces F1136, F2833 and F3019, withdrawn 2025)
Coating
Zinc and aluminium flake basecoat, with or without sealing or lubricated topcoat
Thickness
Typically 8 to 20 µm, depending on system
Chromium
Chromium(VI)-free; ASTM F3393 requires supply without hexavalent chromium
Best for
Property class 10.9 and 12.9, A490-level bolts, studs and nuts
Corrosion test
Typically 500 to over 1000 h neutral salt spray to red rust, depending on system and thickness
Coated hex nuts under red and blue light
Coated nuts (photo for illustration)

What we supply

Metric bolts
ISO 4014 and 4017, class 8.8 to 12.9
Structural bolts
A490-level F3125 bolts where zinc flake is the specified coating (twist-off assemblies only as coated by the bolt manufacturer)
Studs and nuts
Coated studs, nuts and washers to match
Topcoats
Sealed, lubricated or coloured topcoats to the buyer’s specification

Zinc flake, electroplating or hot-dip galvanizing?

The three zinc coatings for fasteners differ in thickness, thread fit and hydrogen risk. The right one depends on bolt strength and exposure.

Zinc coatings for fasteners compared
CoatingStandardTypical thicknessThread fitHydrogen embrittlement
Zinc flakeISO 10683, ASTM F33938 to 20 µmStandard tolerances normally keptNo hydrogen from the coating process
Electroplated zincASTM F1941ThinStandard tolerancesRisk on high-strength parts; baking needed
Hot-dip galvanizingASTM F2329About 50 µmNuts tapped oversizeRestricted on the highest-strength bolts

Zinc flake avoids process hydrogen only if parts are cleaned by alkaline degreasing or shot blasting, not acid pickled or phosphated before coating. It does not make a high-strength bolt immune to hydrogen picked up in service.

Hot-dip galvanized boltsPTFE coated stud bolts

Zinc flake or fluoropolymer (PTFE) coating?

Both are thin coatings, but they do different jobs. Many fluoropolymer systems use a zinc flake primer underneath.

Zinc flake versus fluoropolymer coated fasteners
PointZinc flakeFluoropolymer (e.g. Xylan®)
Main purposeCorrosion protection for high-strength boltsLow friction, colour coding and easy removal of flange studs
Typical parts10.9 and 12.9 bolts, A490-level structural boltsA193 B7 and B7M flange studs with 2H and 2HM nuts
FrictionSet by the topcoat; check the coater’s dataLow, so tightening torque must be reduced
Saudi Aramco flange boltingNot named in SAES-L-109 (2018 issue, unofficial copy)Ceramic-fluoropolymer to 09-SAMSS-107 is one listed option

Saudi Arabia notes for coated bolts

Coating choice on Saudi Aramco jobs depends on the bolting service. Confirm against the current revision of the standards named in your project specification.

Coated fasteners on Saudi projects
PointWhat it means for the order
Flange bolting offshore or undergroundSAES-L-109 (2018 issue, unofficial copy) lists ceramic-fluoropolymer coating per 09-SAMSS-107 as one option, so zinc flake is not the default for these studs.
Structural and equipment boltsZinc flake is chosen by the designer, often for 10.9 and 12.9 or A490-level bolts where hot-dip galvanizing is restricted.
Coating standard on the orderState ISO 10683 or ASTM F3393, the system and any topcoat; older specs that cite F1136 or F2833 refer to standards now replaced by F3393, and we confirm with the buyer which one to certify to.
CoaterThe coating applicator is named on the coating certificate.

JTE supplies coated fasteners through specialist coaters; brand-name systems are supplied only where the coater uses that maker’s product. Based on an unofficial copy of SAES-L-109 (29 January 2018), which may be superseded; confirm against the current revision in your project specification.

Where zinc flake coated bolts are used

Wherever high-strength fasteners need corrosion protection without the thickness or hydrogen risk of other zinc coatings.

High-strength bolts

Property class 10.9 and 12.9 bolts and screws.

Steel structures

A490-level bolts where hot-dip galvanizing is not allowed.

Machinery

Equipment and skid bolting in humid, coastal plants.

Studs and rods

Coated studs where the thread fit must stay standard.

Nuts and washers

Matching coated nuts and washers for each bolt.

Coastal sites

Outdoor bolting at Jubail, Ras Tanura and Yanbu.

Coated to your specification

We source the fasteners and arrange coating with specialist applicators.

  • ISO 10683 or ASTM F3393
  • Chromium(VI)-free systems
  • Sealed or lubricated topcoat
  • Colour topcoats on request
  • Coating thickness report

Coatings and finishes

Documents with every order

Base metal and coating paperwork travel together.

  • EN 10204 3.1 MTC
  • Coating certificate naming the coater
  • Thickness measurements
  • Salt spray report where specified
  • Third-party inspection on request

Quality and certificates

Zinc flake coating questions

Is ASTM F1136 still current?

No. ASTM withdrew F1136, F2833 and F3019 in 2025 and replaced them with ASTM F3393. ISO 10683:2018 remains the international standard.

Does zinc flake cause hydrogen embrittlement?

The coating process produces no hydrogen, which is why it is used on bolts of 1000 MPa and above, provided the parts are not acid pickled or phosphated before coating. It does not protect a bolt from hydrogen picked up in service.

Do zinc flake coated nuts need oversize tapping?

Normally not. The film is typically 8 to 20 µm, much thinner than hot-dip galvanizing, so standard thread tolerances are usually kept.

Is Geomet the same as zinc flake?

Geomet® is a brand of chromium-free zinc flake (NOF Metal Coatings). It was introduced as the chrome-free alternative to Dacromet 380, which contained hexavalent chromium.

Can zinc flake be used on Saudi Aramco flange studs?

The 2018 issue (unofficial copy) of SAES-L-109 lists ceramic-fluoropolymer coating per 09-SAMSS-107 for offshore and underground flange bolting, not zinc flake, so follow the project specification.

Updated

Related

PTFE coated stud bolts

Fluoropolymer coated flange studs.

Hot-dip galvanized bolts

ASTM F2329 galvanized bolts and nuts.

Class 8.8, 10.9 and 12.9 bolts

ISO 898-1 metric bolts.

Need coated high-strength bolts?

Send the bolt list and coating specification: we quote fasteners and coating together.

Request a quote+966 54 614 8678