+966 54 614 8678 [email protected] WhatsApp
JTE FastenersBolting & hardware, Al Jubail العربية Request a quote

ASTM A194 7M heavy hex nuts for low-temperature sour service

Hardness-limited chromium-molybdenum heavy hex nuts for L7M stud bolts on cold flanges and in cold sour service, every nut hardness tested.

ASTM A194 Grade 7M is a quenched and tempered chromium-molybdenum alloy steel heavy hex nut, tempered at 1150 °F or above to keep its hardness between 159 and 237 HB (22 HRC maximum). It is the matching nut for A320 L7M studs, which Saudi Aramco SAES-L-109 lists for low-temperature service down to about −73 °C, including low-temperature sour service.

Material
Cr-Mo alloy steel, quenched and tempered
Min tempering
1150 °F (621 °C)
Hardness
159–237 HB (22 HRC max)
Proof stress
150 ksi (heavy hex)
Hardness testing
Every nut
Pairs with
ASTM A320 L7M
Service
Low temperature to about −73 °C; cold sour
Marking
7M and maker’s mark
Heavy hex nut on a flange stud bolt
A 7M nut looks like any heavy hex nut; the marking and the certificate tell them apart.
Zinc coated heavy hex nuts
Flanged pipe joints clamped with stud bolts and heavy hex nuts

A194 nut grades compared

The five heat-treated grades used on Saudi flanges, side by side.

ASTM A194 heat-treated heavy hex nut grades
GradeMaterialMin temperingHardnessProof stress (heavy hex)Typical stud
2HMedium carbon steel, quenched and tempered850 °F (454 °C)24–38 HRC175 ksi (1,207 MPa)A193 B7
2HMMedium carbon steel, quenched and tempered, hardness-limited1150 °F (621 °C)159–237 HB (22 HRC max)150 ksi (1,034 MPa)A193 B7M
4Carbon-molybdenum steel, quenched and tempered (removed from A194 in 2017)1100 °F (593 °C)24–38 HRC175 ksi (1,207 MPa)A193 B16, A320 L7
7Chromium-molybdenum alloy steel, quenched and tempered1100 °F (593 °C)24–38 HRC175 ksi (1,207 MPa)A320 L7, A193 B16, A193 B7
7MChromium-molybdenum alloy steel, quenched and tempered, hardness-limited1150 °F (621 °C)159–237 HB (22 HRC max)150 ksi (1,034 MPa)A320 L7M

Values from ASTM A194 for heavy hex nuts (coarse and 8-pitch threads); 24–38 HRC is about 248–352 HB. Always order to the edition your specification names.

Nut compatibility chartAll nuts

Saudi Arabia requirements for 7M nuts

In Saudi Aramco SAES-L-109 the L7M / 7M pair covers cold flanges, including cold flanges in sour service.

7M nuts in Saudi Aramco requirements
RequirementWhat it means
Low temperature (SAES-L-109, Table 5)A320 L7M studs with A194 7M nuts, about −73 to 450 °C.
Low-temperature sour serviceThe same L7M / 7M pair covers cold flanges in sour service.
When it applies (13.2.2)Flanges that can auto-refrigerate if they leak.
Hardness limit22 HRC / 237 HB maximum, in line with NACE MR0175 / ISO 15156.
Low-temperature testingSpecify S3 Charpy testing where the project requires impact-tested nuts.
Vendor statusJTE Fasteners is ISO 9001 certified and a registered Saudi Aramco and SABIC vendor.

Summarised from Saudi Aramco SAES-L-109 (29 January 2018 edition). Always work to the current revision, the plant specification and your purchase order.

Where 7M nuts are used

Where bolting has to be both tough in the cold and resistant to H2S.

Cold sour gas lines

Flanges that are both cold and in H2S service.

Gas plant chilling units

Refrigeration and NGL recovery piping.

Auto-refrigerating flanges

Light-ends lines that chill when they leak.

L7M / 7M sets

Studs and nuts certified together.

Coated sets

PTFE-coated L7M studs with 7M nuts.

Hardness records

Hardness results reported on the certificate.

Tested before it ships

Every 7M nut is hardness tested and marked.

  • 159–237 HB
  • 22 HRC maximum
  • Marked 7M
  • Matched to L7M studs

L7 / L7M stud bolts

Documents with every order

Each lot is traceable to its heat and hardness tested.

  • EN 10204 3.1 with heat number
  • Hardness results on the certificate
  • 3.2 with third-party inspection
  • PMI on request

Quality and certificates

A194 7M nut questions

What is an ASTM A194 7M nut?

A hardness-limited heavy hex nut of quenched and tempered chromium-molybdenum alloy steel, 159–237 HB (22 HRC maximum), with a 150 ksi proof stress, used with A320 L7M studs.

When is 7M used instead of Grade 7?

When the bolting must also resist sulfide stress cracking: 7M is limited to 22 HRC, while Grade 7 can reach 38 HRC.

Which stud goes with a 7M nut?

ASTM A320 L7M.

What temperature range does L7M / 7M cover in SAES-L-109?

About −73 to 450 °C, in Table 5.

Is 7M the same as 2HM?

Both are limited to 237 HB with a 150 ksi proof stress, but 7M is chromium-molybdenum alloy steel for low-temperature service, while 2HM is carbon steel for B7M studs.

Related

L7 / L7M stud bolts

The low-temperature stud for 7M nuts.

A194 2HM nuts

Carbon steel sour-service nuts.

Nut compatibility chart

Which nut goes with which bolt.

Cold sour bolting?

Send size and quantity for L7M / 7M sets: hardness tested and certified.

Request a quote+966 54 614 8678