+966 54 614 8678 [email protected] WhatsApp
JTE FastenersBolting & hardware, Al Jubail العربية Request a quote

Lock nuts and special washers for vibrating and live-loaded joints

Prevailing-torque lock nuts, wedge-locking washers, Belleville disc springs, coupling nuts and dome nuts for joints that must not loosen, supplied from Al Jubail with the bolts they fit.

Bolted joints loosen when vibration or movement lets the nut turn, or when the clamped parts relax and the bolt loses tension. Lock nuts resist turning with built-in friction, wedge-locking washers stop rotation with cams steeper than the thread, and Belleville disc springs keep the bolt loaded as a gasket creeps or the joint heats and cools. Split spring washers are no longer recommended: they flatten long before the bolt reaches its tightening load.

Nylon-insert lock nuts
ISO 7040 (regular, DIN 982) and ISO 10511 (thin, DIN 985); -50 °C to +120 °C
All-metal lock nuts
ISO 7042 (DIN 980); -50 °C to +150 °C
Wedge-locking washers
Cam-faced washer pairs, tested by Junker vibration test
Belleville disc springs
EN 16983 (formerly DIN 2093), single or stacked, for flange live loading
Coupling and dome nuts
DIN 6334 long coupling nuts, DIN 1587 domed cap nuts
Materials
Carbon steel class 8 and 10, stainless 304 / 316, alloy steel; plain, zinc or zinc flake

Which locking method to use

Nylon-insert nut
Light to moderate vibration below 120 °C; normally used once
All-metal lock nut
Higher temperatures up to 150 °C and reusable within limits
Wedge-locking washers
Severe vibration and dynamic loads where the nut must not rotate
Belleville disc springs
Flanges and joints that lose tension through gasket creep or thermal cycling
Double nuts
Hanger rods and threaded rod connections

Lock nut and washer standards

Many drawings still quote DIN numbers. The ISO replacements below are the current standards, and both 2012 editions of ISO 7040 and 7042 have been replaced by 2025 editions.

Locking fasteners and their standards
ProductCurrent standardOlder referenceService temperature
Prevailing-torque nut, non-metallic insert, regularISO 7040DIN 982-50 °C to +120 °C (ISO 2320)
Prevailing-torque nut, non-metallic insert, thinISO 10511DIN 985-50 °C to +120 °C
Prevailing-torque nut, all-metalISO 7042DIN 980-50 °C to +150 °C (ISO 2320)
Disc springs (Belleville)EN 16983DIN 2093Depends on material, up to 500 °C or more in special alloys
Split spring lock washerNone (withdrawn)DIN 127Not recommended for locking
Hexagon domed cap nut–DIN 1587 (withdrawn)Per material
Hexagon coupling nut (length 3 x d)–DIN 6334Per material

Temperature limits for prevailing-torque nuts from ISO 2320. Disc spring limits depend on material: spring steel 51CrV4 for normal service, heat-resistant steel or nickel alloys for high temperature.

Heavy hex nutsWashers

Saudi Arabia requirements for locking hardware

Saudi Aramco standards address locking in two places: hanger assemblies on plant piping and live-loaded flange bolting.

Locking hardware in Saudi Aramco projects
RequirementWhat it means for the order
SAES-L-350, hanger assembliesThreaded connections in pipe hanger assemblies need a locking device such as double nuts.
SAES-L-109, Belleville washersBelleville washers may be required for severe cyclic service and for bolting above 450 °C, subject to review by the piping standards committee.
SAES-L-109, flat washersFlat washers under nuts are only required in special cases such as insulating flanges or plastic flanges.
Material and classLock nuts are supplied in the property class or ASTM grade that matches the bolt; nylon-insert nuts are not offered above 120 °C.
Vendor statusJTE Fasteners is ISO 9001 certified and registered as an approved vendor with Saudi Aramco and SABIC.

Summarised from Saudi Aramco SAES-L-350 and SAES-L-109. Project specifications take precedence; send them with the enquiry.

Where locking hardware is used

Anywhere vibration, movement or temperature change can loosen a joint.

Rotating equipment

Pump bases, motor feet and coupling guards on vibrating skids.

Live-loaded flanges

Belleville stacks on heat exchanger and high-temperature flanges.

Pipe hangers

Double nuts and lock nuts on hanger rods and turnbuckles.

Structures and walkways

Grating clips, handrails and ladders exposed to vibration.

Threaded rod connections

Coupling nuts joining rod; dome nuts covering exposed threads.

Maintenance stock

Mixed packs of lock nuts and washers for plant stores.

Choosing the right locking method

The right choice depends on the cause of loosening.

  • Vibration that turns the nut: wedge-locking washers or lock nuts
  • Gasket creep or thermal cycling: Belleville springs
  • Hanger rods: double nuts
  • High temperature: all-metal nuts, not nylon
  • Avoid split spring washers for locking

Bolt torque calculator

Documents with every order

Locking parts are traced like the bolts they go on.

  • Material certificates
  • Property class or grade marking
  • Coating report if coated
  • Disc spring load and deflection data
  • 3.2 with third-party inspection

Quality and certificates

Lock nut and washer questions

What temperature can a nylon-insert lock nut take?

ISO 2320 gives -50 °C to +120 °C for prevailing-torque nuts with a non-metallic insert. Above that, use an all-metal lock nut, which is rated to +150 °C.

Is DIN 985 the same as ISO 7040?

No. ISO 7040 is the regular-height nylon-insert nut that replaced DIN 982. DIN 985 is the thin version, whose ISO equivalent is ISO 10511.

Do split spring washers stop bolts loosening?

Research and the NASA fastener design manual both found that a split spring washer is flat before the bolt is fully tightened and then provides no locking. DIN 127 has been withdrawn; use wedge-locking washers or lock nuts instead.

What does a Belleville washer do on a flange?

A stack of disc springs makes the bolted joint more elastic, so when the gasket creeps or the flange heats and cools, the springs keep load on the bolt. Saudi Aramco SAES-L-109 mentions them for severe cyclic service and bolting above 450 °C.

How do wedge-locking washers work?

Each pair has cams on the inner faces with an angle steeper than the thread pitch. If the nut tries to turn loose, the cams ride up and increase tension, which stops rotation. They are tested with the Junker transverse vibration test.

What locking does Saudi Aramco require on pipe hangers?

SAES-L-350 requires a locking device such as double nuts on threaded connections in hanger assemblies.

Updated

Related

Heavy hex nuts

A194 and A563 nuts in all grades.

Washers

Flat, hardened and plate washers.

Pipe supports and hangers

Clamps, rods and hanger hardware.

Need joints that stay tight?

Send the bolt size, grade and service: we recommend and quote the locking hardware to suit.

Request a quote+966 54 614 8678