+966 54 614 8678 [email protected] WhatsApp
JTE FastenersBolting & hardware, Al Jubail العربية Request a quote

Torque wrenches and bolt tensioners for flange bolting

Manual and hydraulic torque wrenches, torque multipliers, pumps, hoses, impact sockets and hydraulic stud tensioners. Supplied from Al Jubail for plant bolting and shutdowns.

Torque wrenches and bolt tensioners are the two main tool families for tightening flange studs to a controlled load: torque tools turn the nut, while tensioners stretch the stud hydraulically and then run the nut down. JTE supplies manual click and dial torque wrenches and torque multipliers. We also supply hydraulic square-drive and low-profile torque wrenches with pumps, hoses and impact sockets, and hydraulic bolt tensioners. All tools are sourced from established tool makers and ship with the documents their maker issues. We can quote them together with the studs, nuts and gaskets they will tighten.

Manual wrenches
Click (ISO 6789 Type II) and dial (Type I) torque wrenches
Calibration
ISO 6789-2 certificate from the tool maker on request; typical recheck at 12 months or 5,000 cycles
Torque multipliers
Geared hand units with reaction arm; ratio and capacity by model
Hydraulic torque wrenches
Square-drive and low-profile hex-cassette types, typically up to 690 to 700 bar (10,000 psi)
Pumps and hoses
Electric or air-driven pumps; 700 bar twin hoses rated with a 4:1 safety factor
Bolt tensioners
Hydraulic stud tensioners, typically up to 1,500 bar (21,750 psi)
Sockets
Impact sockets to ISO 2725-2 dimensions, metric and inch
Assembly practice
Used to ASME PCC-1 tightening patterns and your plant procedure
Ratchet wrench head used for bolting work
Ratchet wrench head used for bolting work (photo for illustration)

What we supply

Manual torque tools
Click and dial torque wrenches, torque multipliers and adaptors
Hydraulic torque wrenches
Square-drive and low-profile hex-cassette units with reaction arms
Pumps, hoses and gauges
Electric and air pumps, 700 bar twin hoses and couplers
Impact sockets
Square-drive impact sockets for hydraulic wrenches, metric and inch
Bolt tensioners
Stud tensioners, bridges, pullers and 1,500 bar hoses
Shutdown packs
Tools quoted with studs, nuts, washers and gaskets per joint list

Torque wrenches and bolt tensioners: which tool for which job

Pick the tool from the stud size, the load you need, the room around the nuts and how tightly the load must be controlled. The ratings below are typical maker figures.

Torque wrenches and bolt tensioners compared
ToolHow it controls loadTypical rating or toleranceBest for
Click torque wrench (ISO 6789 Type II)Releases with a click at the set torque±4% of set value; ±6% for 10 N·m and below and some classesSmall studs, instrument and utility flanges
Dial torque wrench (ISO 6789 Type I)Shows the applied torque on a dialTolerance set by the ISO 6789 classChecking and auditing torque, small joints
Hand torque multiplierGearbox multiplies the input from a manual wrenchOne maker: 27:1 ratio, 3,400 N·m output, ±4% mean multiplicationMedium studs where no hydraulic set or power is available
Hydraulic square-drive wrenchPiston drives a ratchet; torque set by pump pressureUp to 690 to 700 bar; makers quote ±3%Medium and large flange studs, with impact sockets
Low-profile hex-cassette wrenchSame drive through a slim hex link over the nutOne maker: 26 to 155 mm across flatsTight clearance, heat exchanger and compact flanges
Hydraulic stud tensionerStretches the stud with a puller; nut is run downTypically up to 1,500 barLarge studs, often 2 in. and above, and critical joints

Ratings are typical maker figures, not limits set by a standard. Confirm capacity, drive size and clearance against the tool maker’s data sheet for each joint.

Bolt torque calculatorShutdown bolting kits

Torque or tension: how to choose

Torque tools suit most flanges. Tensioners give a more even stud load on large or critical joints but need longer studs and more room.

Torque tightening versus hydraulic tensioning
FactorTorque toolsHydraulic tensioners
How load is madeThe nut is turned; friction under the nut and in the threads absorbs most of the inputThe stud is stretched directly; friction does not set the load
Commonly quoted preload scatterAbout ±25% to 30% with torque aloneAbout ±10%
Stud lengthStandard length for the flangeOne extra stud diameter of thread above the nut
Load on releaseNo loss from the tool itselfSome load is lost; allowed for by the load transfer factor
ClearanceRoom to swing the wrench and a solid reaction pointRadial room for the bridge and height above the stud
Typical useMost studs up to about 1 1/2 in.Many plants tension at about 2 in. and above, and on critical joints
Simultaneous tighteningUsually one or two tools at a time50% coverage (every other stud) is common; 100% tightens all at once

Scatter figures are commonly quoted industry values. They vary with lubrication, tool condition and operator skill. Your plant procedure decides the method for each joint.

Bolting tools in Saudi plants: what to check

We could not verify a Saudi Aramco or SABIC document on bolting tools on a public web page, so we quote none. The points below cover import conformity, site conditions and common owner requirements.

Points to check for bolting tools used in Saudi Arabia
RequirementWhat it means
SABER import conformityRegulated imported products need a product certificate of conformity (valid one year) and a shipment certificate through SASO’s SABER platform. The HS code decides which regulation applies.
Assembly procedureMany plant owners call up ASME PCC-1 for flange assembly. Check which edition and which tightening patterns your procedure allows.
Qualified assemblersPCC-1 (2022) Appendix A qualification certificates are valid for three years.
Calibration recordsKeep a valid ISO 6789-2 certificate for each manual wrench and a calibration record for each hydraulic tool and gauge, valid through the shutdown.
Hazardous areasElectric pump motors can spark. Makers advise air-driven pumps in explosive atmospheres; check the area classification and permit.
Heat, sand and chloridesKeep couplers capped and tools cased, use the maker’s oil grade, and dry tools used near the sea before storage.
Sour service studsB7M studs have a lower minimum yield (80 ksi) than B7 (105 ksi), so recalculate target stress, torque and pressure for them.

No Saudi Aramco or SABIC document is cited here. Check your project specification, the plant bolting procedure and the current SABER requirements for your HS code.

Where these tools are used

Controlled bolting tools are used wherever a joint must hold pressure or carry a defined load.

Process piping flanges

ASME B16.5 and B16.47 joints in refineries, petrochemical and utility plants.

Heat exchangers

Channel covers and shell flanges where low-profile tools or tensioners fit.

Large studs

Studs of 2 in. and above on high-pressure flanges and vessel joints.

Valves and pumps

Bonnet, cover and nozzle joints during overhaul.

Shutdowns and turnarounds

Tool sets planned against the joint list and packed with fasteners.

Equipment bolting

Controlled torque on machinery, base plates and structural connections.

Tools and fasteners on one order

Bolting tools can be quoted with the studs, nuts, washers and gaskets they will tighten, so one order covers the joint.

  • ISO 6789 torque wrenches
  • Hydraulic wrench sets
  • Impact sockets
  • Stud tensioners
  • Studs cut at our factory in Al-Jubail

Shutdown bolting kits

Documents we pass on

Each tool ships with the documents its maker issues; fasteners carry EN 10204 3.1 certificates.

  • Declaration of conformance
  • ISO 6789-2 certificate on request
  • Pressure-torque chart
  • Hose pressure rating
  • 3.1 MTC for studs and nuts

Quality and certificates

What tools does a bolted flange joint need?

A controlled flange joint needs three things: a tool that reaches the target bolt load, a way to set or measure it, and safe accessories. For most plant flanges that means a manual torque wrench, a hydraulic torque wrench set or a hydraulic stud tensioner.

The choice depends on stud diameter, the load required, the room around the nuts and how closely the load must be controlled. Small studs are usually tightened with click wrenches. Larger studs need a torque multiplier or hydraulic wrench, and the largest or most critical joints are often tensioned.

Every method relies on the same basics: clean threads, the right lubricant, hardened washers where specified, a tightening pattern and a record. The tool only delivers the load the procedure asks for, so the procedure comes first.

The tool families at a glance

The list below covers what JTE supplies for flange and equipment bolting. All tools come from established tool makers; we do not manufacture tools.

  • Manual torque wrenches: click (setting) and dial (indicating) types to ISO 6789.
  • Torque multipliers: geared hand units that multiply the torque from a manual wrench.
  • Hydraulic torque wrenches: square-drive units that take impact sockets, and low-profile hex-cassette units for tight spaces.
  • Pumps, hoses and gauges: electric or air-driven pumps, twin hoses and couplers rated for the system pressure.
  • Impact sockets: square-drive sockets made for machine and hydraulic use.
  • Hydraulic bolt tensioners: load cells, bridges, pullers, sockets and high-pressure hoses.

Manual click and dial torque wrenches and ISO 6789

Manual torque wrenches are covered by ISO 6789, which has had two parts since the 2017 revision. Part 1 sets design and quality requirements and the maker’s declaration of conformance. Part 2 sets how a traceable calibration is done and what the certificate states, including measurement uncertainty.

ISO 6789 has two tool types. Type I covers indicating tools such as dial, beam and electronic wrenches. Type II covers setting tools such as click wrenches. Each type is split into classes. The class decides the test points and the allowed deviation.

A typical industrial click wrench must stay within ±4% of the set value. Tools of 10 N·m and below, and some classes, are allowed ±6%. Some makers state ±3% for their own wrenches, but the marked class still governs the acceptance check.

Testing is done at the bottom of the range (usually 20% of maximum), at 60% and at 100%. Tool makers describing ISO 6789-2 give five readings per test point. Any reading outside tolerance fails the wrench.

Calibration interval and certificates

The usual recheck interval is 12 months or 5,000 cycles, whichever comes first, counted from when the wrench enters service. Your quality system can set a shorter interval for heavy use.

A new wrench usually comes with a declaration of conformance to Part 1. If your site needs a traceable certificate, ask for one to ISO 6789-2 on the purchase order. It records the readings, the deviation and the uncertainty at each test point.

Recheck a wrench before further use after a drop, an overload, a repair or an unexplained leak on joints it tightened. In the United States, ASME B107.300 (Torque Instruments) is the equivalent reference.

Worked example: a 40 to 200 N·m click wrench

The table shows the acceptance bands for a 40 to 200 N·m click wrench with a ±4% tolerance. A mean reading of 37.6 N·m at the 40 N·m point is −6.0%. The wrench fails, even if it passes at 120 and 200 N·m.

Using a manual wrench well

  • Pull smoothly at the handle grip and stop at the click; do not keep pulling after it releases.
  • Work between about 20% and 100% of the wrench range, not at the very bottom.
  • If you add an extension, correct the setting: set torque = target torque × wrench length ÷ total length.
  • Store click wrenches at the lowest scale setting, never below it.
  • Do not use a torque wrench to break out seized nuts.
ISO 6789 acceptance bands for a 40 to 200 N·m wrench at ±4%
Check pointSet valueLower limitUpper limit
20%40 N·m38.4 N·m41.6 N·m
60%120 N·m115.2 N·m124.8 N·m
100%200 N·m192.0 N·m208.0 N·m

Limits are the set value ±4%. Small wrenches and some classes use ±6%; check the class on the wrench and its certificate.

Torque multipliers

A torque multiplier is a planetary gearbox that multiplies the torque from a manual wrench. It lets one person reach several thousand newton metres without a hydraulic set or a power supply.

The nominal gear ratio is not the exact output multiple, because the gearbox loses some torque to friction. Makers therefore publish a multiplication factor or calibration for each unit. One maker lists a 27:1 unit with 3,400 N·m maximum output and a mean multiplication accuracy of ±4%.

The multiplier must react against something solid, usually an adjacent nut, through its reaction arm or plate. The input wrench is set to the target output divided by the multiplication factor.

When a multiplier is the right choice

  • Studs too large for a manual wrench, where a hydraulic set is not available.
  • Remote locations without electric power or compressed air.
  • A small number of joints, where setting up pumps and hoses takes longer than the work.
  • Controlled breakout of nuts, within the unit’s rated capacity.

Points to check

  • Input and output square drive sizes match your wrench and sockets.
  • The reaction arm shape fits the flange and the adjacent nut.
  • The multiplication factor is stated on the certificate or data sheet.
  • Output capacity covers both tightening and the expected breakout torque.

Hydraulic torque wrenches, pumps, hoses and sockets

A hydraulic torque wrench uses a piston to drive a ratchet in short strokes. Its torque is set by the pump pressure, so the operator sets a pressure from the tool’s pressure-torque chart rather than reading torque directly.

Industrial sets usually work at up to 690 to 700 bar (10,000 psi). Makers commonly quote ±3% torque accuracy for the tool itself. Output rises roughly in proportion to pressure; one maker lists each drive unit’s maximum torque at 10,000 psi and its minimum at 1,000 psi.

Square-drive or low-profile?

A square-drive wrench turns a standard impact socket and comes with a reaction arm. It is the general-purpose choice for flange studs where there is room above the nut.

A low-profile wrench uses a slim hex cassette that fits straight over the nut. It is used where space above or beside the nut is limited, such as heat exchanger and compact flanges. Some makers offer one drive unit that accepts either cassette type.

Hex cassette ranges vary by maker. One maker’s low-profile range runs from about 26 to 155 mm (roughly 1 to 6 1/8 in.) across flats.

Pumps and hoses

Pumps are electric or air-driven. Electric motors can spark, so makers advise air-driven pumps in explosive atmospheres or where conductive liquids are present. Check the hazardous-area classification before you choose.

Torque wrenches use a twin hose: one line advances the piston and the other retracts it. Makers rate these hoses at 700 bar with a 4:1 safety factor. Use one twin hose set between pump and tool. Never mix in hoses or couplers from tensioning equipment, which runs at a higher pressure.

Reaction arms and sizing

The reaction arm must bear squarely on a solid point, usually the adjacent nut, never on the pipe, a gauge or insulation. Most square-drive reaction arms can be set through 360 degrees around the drive.

Size the wrench for breakout as well as make-up. One maker’s rule of thumb is that loosening needs about 250% of the tightening torque. A tool sized only for make-up may stall on a seized nut.

Impact sockets

Use impact sockets, not chrome hand sockets, on hydraulic square-drive wrenches. ISO 2725-2 sets dimensions for machine-operated impact sockets, and ISO 1711-2 sets their hardness and minimum torsional strength.

Order sockets by drive size and nut size across flats. Heavy hex nuts on flange studs are larger across flats than standard hex nuts of the same thread, so check the nut standard first.

How hydraulic bolt tensioners work

A hydraulic bolt tensioner stretches the stud directly instead of turning the nut against friction. A load cell sits on a bridge over the nut, and a puller threads onto the stud end above it.

When pressure is applied, the piston pulls the stud and it stretches elastically. The operator then turns the nut down to the flange face through a window in the bridge. When pressure is released, the nut holds the stretch and the stud stays loaded.

Topside tensioners commonly work at up to 1,500 bar (21,750 psi). They need their own pump, hoses and couplers, separate from 700 bar torque wrench equipment. The sequence below is typical; follow the tool maker’s manual and your procedure.

Load transfer factor

Some stretch is lost when pressure is released, because the nut threads and the joint settle as they take the load. The tensioner must therefore apply more load than the residual load you need.

The ratio between the applied load and the residual load is the load transfer factor (LTF). One maker’s data sheet uses LTF = 1.01 + stud diameter ÷ grip length, with a minimum of 1.10. Short, thick joints lose more load than long, slender ones.

Worked example from that data sheet: a 1 7/8 in. stud with a 204 mm grip gives LTF = 1.01 + 47.625 ÷ 204 = 1.243. For a residual load of 430.9 kN, the tensioner must apply about 535.6 kN. The same sheet says to check that the applied load stays below 95% of the stud’s yield load.

Longer studs and extra thread length

Tensioning needs extra thread above the nut for the puller to grip. Add one stud diameter to the length you would use for torque tightening. A 2 in. stud therefore needs about 2 in. of extra length on the tensioned side.

Order tensioning studs to that longer length, or the tools cannot be fitted. Check also that there is radial room for the bridge between adjacent studs, and that nothing blocks the tool above the stud.

Coverage: 50% or 100%

With 50% coverage, one tensioner is fitted to every other stud; this is common practice. The first set is tensioned, then the tools move to the second set. Some load is lost from the first set as the second is tightened, so the procedure adds a check pass.

With 100% coverage, every stud has a tool and all are tensioned together, which gives the most even gasket load. Coverage of 25% is possible but needs more passes and is less accurate.

  1. Check that each stud has at least one stud diameter of free thread above the nut.
  2. Fit the bridge over the nut and the socket on the nut, then thread the puller fully onto the stud.
  3. Connect the hoses between the tools and check every coupler is fully engaged.
  4. Raise pressure to the calculated value, staying within the tool’s stroke limit.
  5. Run the nut down firmly against the flange with the tommy bar through the bridge window.
  6. Release pressure slowly, then repeat or carry out a check pass as the procedure requires.
  7. Remove the tools and record pressures, passes and any stud that did not hold.

ASME PCC-1 bolted flange joint assembly

ASME PCC-1, Guidelines for Pressure Boundary Bolted Flange Joint Assembly, is the reference most plants use for flange make-up. It covers cleaning, alignment, gasket installation, lubrication, bolt numbering, tightening, target torque, testing and records. Published editions include 2010, 2013 and 2022.

PCC-1 is a guideline, not a law. Your plant or project procedure decides which parts apply, which tightening patterns are allowed and which records you keep.

Target bolt stress range

PCC-1 suggests a target assembly bolt stress of about 40% to 70% of the bolt’s yield strength. Too little load may not seat the gasket; too much risks crushing the gasket or damaging the flange or bolts.

For A193 B7 studs up to 2 1/2 in., with 105 ksi minimum yield, that range is about 42 to 74 ksi. The 2010 and 2013 editions give reference torque values based on 50 ksi (345 MPa) on the root area. Appendix O of those editions explains how to select a joint-specific assembly bolt stress.

Legacy cross pattern

The legacy pattern tightens the studs in a star (cross) order in rising steps. A typical sequence is shown below.

  • Pass 1: 20% to 30% of target torque, in star order.
  • Pass 2: 50% to 70% of target torque, in star order.
  • Pass 3: 100% of target torque, in star order.
  • Final passes: circular, clockwise, at 100% until the nuts no longer turn.

Alternative patterns

PCC-1 also gives alternative patterns that reach full load in fewer passes. In the modified star pattern, the first four studs go to 20% to 30% and the next four to 50% to 70%. The rest go to 100%, followed by circular passes.

The quadrant pattern works around the flange in groups in a similar way. These alternatives save the most time on flanges with 20 or more studs; on 12 studs or fewer the saving is small.

A circular-only pattern is limited to hard gaskets such as kammprofile, and is not used with spiral wound, RTJ or double-jacketed gaskets. Spiral wound and kammprofile gaskets usually need about two final circular passes; RTJ gaskets often need more.

Records and qualified assemblers

PCC-1 includes example joint assembly records. A good record lists joint ID, gasket, stud material and lubricant. It also lists the tool serial number, calibration date, target torque or pressure, passes and assembler.

The 2022 edition sets training and qualification for bolted joint assembly personnel in Appendix A. It builds on a base bolting assembler qualification, with endorsements for powered equipment such as hydraulic torque and tensioning tools, heat exchangers and special joints. Qualification certificates are valid for three years.

Torque or tension: choosing the method

Torque is simpler, cheaper and fits most joints; tensioning gives a more even and more predictable stud load on large or critical joints. The decision is usually written into the plant procedure by stud size and service.

With torque, most of the input is used to overcome friction under the nut face and in the threads. Only the remainder stretches the stud. A change in lubricant or thread condition therefore changes the preload, even when the torque reading is correct.

Commonly quoted preload scatter is about ±25% to 30% for torque alone and about ±10% for hydraulic tensioning. Elongation measurement can do better again. Treat these as indications, not guarantees.

Worked example: the nut factor effect

The short-form torque equation is T = K × D × F ÷ 12. T is torque in ft-lb, K the nut factor, D the nominal diameter in inches and F the stud load in lbf.

Take a 1 in. stud with a target load of 30,000 lbf and a nickel anti-seize with K = 0.16. Then T = 0.16 × 1 × 30,000 ÷ 12 = 400 ft-lb (about 542 N·m).

Now suppose the threads were only machine oiled and the real K was 0.20. The same 400 ft-lb gives 400 × 12 ÷ (0.20 × 1) = 24,000 lbf. That is 20% below target, with a correctly calibrated wrench. Use our bolt torque calculator with your own K value.

Typical size thresholds

Many sites tighten studs below about 1 in. with manual wrenches, and use hydraulic torque wrenches from about 1 to 1 1/2 in. Many plants switch to tensioning at about 2 in. and above, and on critical joints such as heat exchanger and high-pressure flanges. These are habits, not rules; follow your procedure.

Common mistakes

  • Using a nut factor that does not match the lubricant actually applied.
  • Ordering standard-length studs for a joint that will be tensioned.
  • Reacting a hydraulic wrench on a pipe, gauge or insulation instead of a nut.
  • Skipping the final circular passes because the star passes looked complete.
  • Mixing 700 bar torque wrench hoses with 1,500 bar tensioner hoses or couplers.
  • Letting calibration certificates expire in the middle of a shutdown.

Checking bolt load by elongation

Measuring how much a stud stretches is the most direct field check of bolt load. It takes friction out of the result and is used on critical joints or to prove a torque procedure.

Elongation follows Hooke’s law: ΔL = σ × L ÷ E, where σ is the stud stress, L the effective length and E the elastic modulus. Effective length is the grip length plus an allowance for nut engagement. Use about 200 GPa (29,000 ksi) for alloy steel studs such as B7.

Example: a B7 stud at 50 ksi (345 MPa) with an effective length of 6 in. (150 mm) stretches about 50 × 6 ÷ 29,000 = 0.010 in., or about 0.26 mm. Numbers this small show why measurement must be careful and consistent.

Measuring methods

  • Ultrasonic gauges measure the time a sound pulse takes to travel along the stud before and after tightening. ASTM E1685 sets the practice for fasteners of 6.3 mm (0.25 in.) and larger with an effective length at least twice the diameter.
  • Micrometers or depth gauges measure stud length end to end, before and after tightening.
  • In every method, take a zero reading on each stud before tightening and mark the stud so the same points are measured again.

Practical tips

Prepare stud ends flat and clean for ultrasonic measurement, and record the temperature, since steel length changes with it. Measure a sample of studs on each joint, or every stud on critical joints, as your procedure requires.

If elongation is low across a whole joint, check the nut factor and lubricant first. If a single stud is low, check its threads, nut and washer before adding load.

Safety with hydraulic bolting tools

Hydraulic bolting tools put large forces into small spaces. The main hazards are pinch points at the reaction arm, failed hoses or couplers, and tensioner parts thrown off under load.

Makers design square-drive wrenches to enclose moving parts and reduce pinch points, but the reaction arm still swings hard when the tool starts. Keep hands clear of the arm and the reaction point once pressure is applied.

  • Inspect hoses and couplers before each shift; replace any that are cut, crushed, kinked or leaking.
  • Check couplers are fully engaged before pressurizing; they cannot be tightened by hand under pressure.
  • Never use hoses, couplers or gauges rated below the pump’s maximum pressure.
  • Keep the tensioner puller fully threaded; poor engagement can strip threads and throw the tool.
  • Stand to the side of a tensioner, never directly above the puller, while pressure is applied.
  • Keep tensioner stroke within the tool limit; use tools with stroke indicators or over-stroke protection.
  • Never feel for a hose leak by hand; high-pressure oil can pierce skin.
  • Use air-driven pumps where electric equipment is not allowed by the area classification.
  • Barricade the work area and follow the site permit to work.

Planning bolting tools for Saudi shutdowns and turnarounds

In a plant shutdown, bolting tools sit on the critical path: a missing socket or a failed hose stops work on a joint. Planning the tool list from the joint list avoids that.

Whether the work is in Jubail Industrial City, Ras Al Khair or Ras Tanura, the same planning steps apply. Start early enough to confirm calibration dates and to order longer studs for tensioned joints.

What to put on the RFQ

  • Tool type and quantity, with range and drive size for each wrench.
  • Torque or load range needed, and the largest breakout torque expected.
  • Nut sizes across flats for sockets or hex cassettes.
  • Stud diameters and thread pitch for tensioner pullers.
  • Pump power: electric (with voltage) or air, and any hazardous-area requirement.
  • Hose lengths and the number of tools per pump.
  • Certificate required: declaration of conformance or ISO 6789-2 calibration certificate.
  • Fasteners and gaskets to pack with the tools, and EN 10204 3.1 certificate needs.

Heat, sand and coastal storage

Keep tools in their cases between uses, and cap couplers so sand and dust cannot get in. Use the hydraulic oil grade the maker specifies, and keep pumps out of direct sun where you can.

Near the sea, chlorides attack exposed steel. Wipe and dry tools after use and store them indoors. Recheck any wrench that has been dropped, or soaked in rain or washdown, before it is used again.

  1. List every joint with flange size, class, gasket, stud size and number of studs.
  2. Assign a method (manual torque, hydraulic torque or tensioning) to each joint from your procedure.
  3. Calculate target torque or tensioner pressure for each stud size and lubricant.
  4. Check clearance at each joint for the reaction arm, cassette or tensioner bridge.
  5. Count tools, sockets, cassettes and tensioners by size, plus spares for critical sizes.
  6. Add pumps, twin hoses, tensioner hoses, couplers, gauges and spare seals.
  7. Confirm calibration certificates stay valid until after the shutdown ends.
  8. Pack studs, nuts, washers and gaskets per joint, tagged with the joint ID.

Torque wrench and bolt tensioner questions

What is the difference between a torque wrench and a bolt tensioner?

A torque wrench turns the nut, and the stud load depends on how much of that torque is lost to friction. A hydraulic bolt tensioner pulls the stud with a hydraulic puller and stretches it directly. The nut is then run down to hold the stretch. Tensioning gives a more even load but needs longer studs, more room around the nuts and a 1,500 bar pump.

How accurate does a click torque wrench have to be under ISO 6789?

A typical industrial click wrench, ISO 6789 Type II, must stay within ±4% of the set value at each test point. Tools of 10 N·m and below, and some classes, are allowed ±6%. Testing is done at the bottom of the range, at 60% and at 100% of maximum. The class marked on the wrench and its certificate governs acceptance.

How often should torque wrenches be calibrated?

The usual interval is 12 months or 5,000 cycles, whichever comes first, counted from when the wrench enters service. Your quality system can set a shorter interval for heavy use. Recheck a wrench before further use after a drop, an overload, a repair or an unexplained leak on joints it tightened.

What is the difference between a declaration of conformance and a calibration certificate?

Since 2017, ISO 6789 has two parts. A declaration of conformance under Part 1 is the maker’s statement that the tool meets the design and accuracy requirements. A calibration certificate under Part 2 records the actual readings, deviations and measurement uncertainty from a traceable calibration. Ask for the Part 2 certificate on your order if your site requires one.

What pressure do hydraulic torque wrenches and bolt tensioners use?

Hydraulic torque wrenches typically work at up to 690 to 700 bar (10,000 psi), with twin hoses rated at that pressure. Topside bolt tensioners commonly work at up to 1,500 bar (21,750 psi) and need their own hoses, couplers and pump. Never mix the two systems, and never use a component rated below the pump’s maximum pressure.

Why do tensioned studs need to be longer?

The tensioner’s puller must thread onto the stud above the nut. That needs about one stud diameter of free thread beyond the nut. Tensioning studs are therefore ordered one diameter longer than torque-tightened studs for the same joint. If the studs are too short, the tool cannot be fitted and the joint has to be torqued instead.

What is the load transfer factor in bolt tensioning?

The load transfer factor is the ratio of the load the tensioner applies to the load left in the stud after pressure is released. Some load is lost as the nut and joint settle. One maker uses LTF = 1.01 + stud diameter ÷ grip length, with a minimum of 1.10. Short, thick joints have a higher factor and need more applied load.

What tightening pattern does ASME PCC-1 recommend?

PCC-1 gives a legacy cross pattern: star-order passes at 20% to 30%, 50% to 70% and 100% of target torque, then circular passes at 100% until the nuts stop turning. It also gives alternative patterns, such as the modified star and quadrant patterns. These reach full load in fewer passes and save time on flanges with many studs.

What target bolt stress does ASME PCC-1 suggest?

PCC-1 suggests a target assembly bolt stress of about 40% to 70% of the bolt’s yield strength. For A193 B7 studs up to 2 1/2 in., that is about 42 to 74 ksi. The 2010 and 2013 editions base their reference torque tables on 50 ksi on the root area. The joint-specific value depends on the gasket and flange.

Can I use chrome hand sockets on a hydraulic torque wrench?

No. Use impact sockets made for machine and hydraulic use. ISO 2725-2 sets their dimensions, and ISO 1711-2 sets their hardness and minimum torsional strength. Order them by square drive size and by the nut size across flats; heavy hex flange nuts are larger across flats than standard hex nuts of the same thread.

How do I check the bolt load after tightening?

Measure stud elongation. Take a zero reading on each stud before tightening and measure again afterwards, with an ultrasonic gauge or a micrometer. Elongation equals stress times effective length divided by the elastic modulus. A B7 stud at 50 ksi with a 6 in. effective length stretches about 0.010 in. (0.26 mm).

Does JTE supply bolting tools together with the fasteners?

Yes. We supply manual and hydraulic torque wrenches, pumps, hoses, sockets and bolt tensioners from established tool makers. We can quote them with the studs, nuts, washers and gaskets for the same joints. Studs are cut and threaded at our factory in Al-Jubail and carry EN 10204 3.1 certificates.

Updated

Related

Bolt torque calculator

Work out target torque from stud size, stress and nut factor.

ASTM A193 B7 stud bolts

Flange studs and 2H nuts, including longer studs for tensioning.

Spiral wound gaskets

The gasket most flange tightening patterns are written for.

Send your joint list or tool list

Tell us the tools, ranges and drive sizes you need, or send the joint list, and we will quote tools and fasteners together.

Request a quote+966 54 614 8678