Pipe supports, clamps and hangers for Saudi plant piping
Pipe clamps, U-bolts, beam clamps, strut channel, threaded rod hangers and pipe shoes to MSS SP-58, hot-dip galvanized for Gulf conditions and supplied with the bolts and nuts that go with them from Al Jubail.
Pipe supports carry the weight of piping and control how it moves as it heats, cools and vibrates. The hardware ranges from U-bolts and two-bolt clamps that hold a line to a steel member, to clevis and rod hangers that hang it from above, beam clamps that attach without welding, strut channel for small-bore racks, and shoes that let insulated lines slide. Hanger and support components are designed and made to MSS SP-58, which replaced the withdrawn SP-69.
- Standard
- MSS SP-58 (pipe hangers and supports; replaces SP-69, SP-77, SP-89 and SP-90)
- Products
- U-bolts, pipe clamps, riser clamps, beam clamps, clevis hangers, rod hangers, turnbuckles, strut channel and fittings, pipe shoes and guides
- Materials
- Carbon steel, hot-dip galvanized; stainless 304 / 316 for corrosive areas
- Galvanizing
- ASTM A123 for clamps, shoes and strut; ASTM A153 or F2329 for bolts, nuts, rods and threaded parts
- Pipe sizes
- 1/2 in. to large bore, to MSS type numbers or your support drawing
- Documents
- Material certificates, galvanizing thickness report, dimensional check
Support types we supply
- U-bolts (MSS Type 24)
- Hold a line to a beam or sleeper; plain, galvanized or PTFE-lined
- Pipe clamps (Type 3, 8)
- Two-bolt and riser clamps for vertical and horizontal lines
- Beam clamps (Type 19, 21, 30)
- Attach hangers to steel beams without welding
- Clevis and rod hangers (Type 1)
- Hang lines from above on threaded rod with turnbuckles
- Strut channel 41 x 41
- Channel, brackets, channel nuts and pipe clamps for small-bore racks
- Pipe shoes and guides
- Let insulated and hot lines slide or guide them in one direction
Framing for supports and cable runs: Strut channel and fittings, with Hose clamps and cable ties and Self-drilling screws and drop-in anchors for light fixings.
Common pipe support hardware and its MSS type
MSS SP-58 keeps the type numbers engineers know from SP-69, so most support drawings can be quoted directly from the type number and pipe size.
| Component | MSS type | Typical use |
|---|---|---|
| Clevis hanger | Type 1 | Hanging insulated and uninsulated lines from rod |
| Double-bolt pipe clamp | Type 3 | Suspending lines where a clevis cannot be used |
| Riser clamp | Type 8 | Supporting vertical risers at floor or beam level |
| Turnbuckle | Type 13 | Adjusting rod hanger length |
| Wide-throat top beam C-clamp | Type 19 | Attaching rod to the top flange of a beam |
| Centre-load beam clamp | Type 21 | Hanging from the bottom flange of a beam |
| U-bolt | Type 24 | Holding a line to a beam, sleeper or support steel |
| Pipe saddle and protection saddle | Type 36, 39 | Protecting insulation at the support point |
Type numbers as used in manufacturers’ MSS SP-58 catalogues. Pipe shoes, slides and guides are usually made to the plant’s own support standard drawings.
Saudi Arabia requirements for pipe supports
Saudi Aramco plant piping is supported to SAES-L-120 (flexibility analysis) and installed to SAES-L-350 (construction of plant piping). Both set rules that affect which support hardware is ordered.
| Requirement | What it means for the order |
|---|---|
| SAES-L-350, rod hangers | Rod hangers are not used for lines NPS 12 and larger in liquid or multi-phase service, and rod hangers carry tension only. |
| SAES-L-350, threaded hanger connections | Threaded connections in hanger assemblies need a locking device such as double nuts, so we supply hanger rods with two nuts per connection. |
| SAES-L-350, spring supports | Springs must be in compression, with travel stops painted red and tagged for removal after hydrotest. |
| SAES-L-120, sliding supports | Pipe stress analysis uses a friction factor of 0.20 for PTFE on steel and 0.10 for PTFE on PTFE, against 0.40 for steel on steel, which is why PTFE slide plates are used on long hot lines. |
| Galvanizing | Where the project specifies galvanized supports, clamps and shoes are galvanized to ASTM A123, and bolts and nuts to ASTM A153 or F2329 with nuts tapped oversize. |
| Vendor status | JTE Fasteners is ISO 9001 certified and registered as an approved vendor with Saudi Aramco and SABIC. |
Summarised from Saudi Aramco SAES-L-350 and SAES-L-120. Support types and dimensions follow the project’s support standard drawings; send them with the enquiry.
Where pipe support hardware is used
Every plant piping system needs supports, and most maintenance jobs need replacement clamps and U-bolts.
Pipe racks
U-bolts and guides holding lines on rack beams and sleepers.
Utility and small-bore lines
Strut channel racks with pipe clamps for instrument air, water and drains.
Equipment piping
Hangers and clamps around pumps, exchangers and compressors.
Insulated hot lines
Pipe shoes and saddles that let insulated lines slide without crushing insulation.
Coastal plants
Hot-dip galvanized supports for Jubail, Ras Tanura and Ras Al Khair.
Shutdown packs
Replacement clamps, U-bolts, rods and nuts packed by line or area.
Complete with the fasteners
A support is only finished when its bolts, rods and nuts are on site. We supply them together.
- U-bolts with nuts and washers
- Hanger rod with double nuts
- Clamp bolts galvanized to match
- PTFE pads where specified
- Packed and labelled by support number
Documents with every order
Support hardware is inspected before installation like any other piping material.
- Material certificates
- Galvanizing thickness report
- Dimensional check against the drawing
- MSS type and size on each label
- 3.2 with third-party inspection
Pipe support questions
Is MSS SP-69 still a valid standard?
No. MSS withdrew SP-69 in 2014 and its content now lives in MSS SP-58, together with the former SP-77, SP-89 and SP-90. Support type numbers such as Type 24 for U-bolts are still used.
Which galvanizing standard applies to pipe supports?
Clamps, shoes, strut and other fabricated or rolled parts are galvanized to ASTM A123. Bolts, nuts, threaded rod and other parts that are centrifuged after dipping are galvanized to ASTM A153 or, for fasteners, ASTM F2329.
Can rod hangers be used on large lines in Saudi Aramco plants?
Saudi Aramco SAES-L-350 does not allow rod hangers on lines NPS 12 and larger in liquid or multi-phase service, and rod hangers may carry only tension.
Why do hanger rods need two nuts?
SAES-L-350 requires a locking device such as double nuts on threaded connections in hanger assemblies, so that vibration cannot back the nut off.
Why use PTFE slide plates on pipe shoes?
PTFE on steel has a friction factor of about 0.20 and PTFE on PTFE about 0.10, against 0.40 for steel on steel, so thermal movement puts much less load on the supports and nozzles.
Do you supply strut channel and fittings?
Yes. 41 x 41 mm strut channel in pre-galvanized, hot-dip galvanized and stainless finishes, with brackets, channel nuts and pipe clamps.
Updated
Related
U-bolts
Pipe U-bolts in all sizes and finishes.
Threaded rods
Hanger rod and studding with nuts.
Lock nuts and special washers
Locking nuts and washers for vibrating joints.
Need pipe support hardware?
Send the support schedule or drawing: we quote clamps, U-bolts, rods and fasteners together.