+966 54 614 8678 [email protected] WhatsApp
JTE FastenersBolting & hardware, Al Jubail العربية Request a quote

ASTM A194 2H heavy hex nuts for B7 stud bolts

Quenched and tempered carbon steel heavy hex nuts for B7 studs on high-pressure and high-temperature flanges: the standard flange nut in Saudi refinery and petrochemical plants.

ASTM A194 Grade 2H is a quenched and tempered medium carbon steel heavy hex nut with a proof stress of 175 ksi and a hardness of 24 to 38 HRC. It is the matching nut for ASTM A193 B7 stud bolts, and Saudi Aramco SAES-L-109 pairs B7 with 2H for general service from about −40 to 450 °C. JTE Fasteners supplies 2H nuts in UNC and 8UN threads, plain, galvanized or PTFE coated, with EN 10204 3.1 certificates.

Material
Medium carbon steel, quenched and tempered
Min tempering
850 °F (454 °C)
Hardness
24–38 HRC
Proof stress
175 ksi (heavy hex)
Marking
2H and maker’s mark
Pairs with
ASTM A193 B7
Threads
UNC to 1″; 8UN above 1″
Finishes
Plain, hot-dip galvanized, PTFE / Xylan
Heavy hex bolts and nuts
Heavy hex nuts are thicker and wider than standard hex nuts, which is why flange standards call for them.
Zinc coated heavy hex nuts
Flanged pipe joints clamped with stud bolts and heavy hex nuts

A194 nut grades compared

The five heat-treated grades used on Saudi flanges, side by side.

ASTM A194 heat-treated heavy hex nut grades
GradeMaterialMin temperingHardnessProof stress (heavy hex)Typical stud
2HMedium carbon steel, quenched and tempered850 °F (454 °C)24–38 HRC175 ksi (1,207 MPa)A193 B7
2HMMedium carbon steel, quenched and tempered, hardness-limited1150 °F (621 °C)159–237 HB (22 HRC max)150 ksi (1,034 MPa)A193 B7M
4Carbon-molybdenum steel, quenched and tempered (removed from A194 in 2017)1100 °F (593 °C)24–38 HRC175 ksi (1,207 MPa)A193 B16, A320 L7
7Chromium-molybdenum alloy steel, quenched and tempered1100 °F (593 °C)24–38 HRC175 ksi (1,207 MPa)A320 L7, A193 B16, A193 B7
7MChromium-molybdenum alloy steel, quenched and tempered, hardness-limited1150 °F (621 °C)159–237 HB (22 HRC max)150 ksi (1,034 MPa)A320 L7M

Values from ASTM A194 for heavy hex nuts (coarse and 8-pitch threads); 24–38 HRC is about 248–352 HB. Always order to the edition your specification names.

Nut compatibility chartAll nuts

Saudi Arabia requirements for 2H nuts

Saudi Aramco SAES-L-109 names 2H as the nut for B7 studs in general flange service, and limits where that pair may be used.

2H nuts in Saudi Aramco requirements
RequirementWhat it means
General service (SAES-L-109, Table 5)A193 B7 studs with A194 2H nuts, about −40 to 450 °C.
Wet sour service (13.2.3)Not 2H: use B7M studs with 2HM nuts where flanges are directly or potentially exposed.
Low temperature (13.2.2)Not 2H where a flange can auto-refrigerate when it leaks: use L7M / 7M, or L7 with Grade 4 or 7 nuts.
Galvanizing (12-SAMSS-007, 5.2)A194 material is excluded from the galvanize-everything rule. Where galvanized nuts are ordered, they are tapped oversize so they still fit the coated stud.
Aggressive environments (13.3)Coated bolting to 09-SAMSS-107, corrosion-resistant alloys, paint and seal, or heat-shrink encapsulation.
Vendor statusJTE Fasteners is ISO 9001 certified and a registered Saudi Aramco and SABIC vendor.

Summarised from Saudi Aramco SAES-L-109 (29 January 2018 edition). Always work to the current revision, the plant specification and your purchase order.

Where 2H nuts are used

Anywhere B7 studs hold a flange.

Process piping flanges

ASME B16.5 and B16.47 joints in refinery and petrochemical lines.

Pumps and compressors

Casing and nozzle studs on rotating equipment.

Valve bonnets

Body-bonnet studs on gate, globe and check valves.

Shutdown kits

Studs, 2H nuts and gaskets kitted flange by flange.

Coated sets

2H nuts coated together with their B7 studs.

Heat exchangers

Channel and shell flange bolting.

Stocked and machined in Jubail

2H nuts in common sizes are kept in stock; larger and 8UN sizes are machined in our factory.

  • UNC to 1″, 8UN above
  • 1/2″ to 4″
  • Heavy hex to ASME B18.2.2
  • Grade and maker marked

Custom manufacturing

Documents with every order

Each lot is traceable to its heat and hardness tested.

  • EN 10204 3.1 with heat number
  • Hardness results on the certificate
  • 3.2 with third-party inspection
  • PMI on request

Quality and certificates

A194 2H nut questions

What is an ASTM A194 2H nut?

A heavy hex nut of quenched and tempered medium carbon steel, with a hardness of 24–38 HRC and a proof stress of 175 ksi, made to ASTM A194 for high-pressure and high-temperature bolting.

Which stud bolt goes with a 2H nut?

ASTM A193 B7. Saudi Aramco SAES-L-109 pairs B7 studs with 2H nuts for general service; Grade 7 nuts are also compatible with B7.

Can 2H nuts be used in sour service?

Not normally. Sour service needs hardness-limited nuts: Grade 2HM (22 HRC maximum) with B7M studs, per NACE MR0175 / ISO 15156 and SAES-L-109.

What is the difference between 2H and 2HM?

2HM is tempered hotter (1150 °F against 850 °F), so its hardness stays at or below 237 HB / 22 HRC and every nut is hardness tested. 2H is harder and stronger, with a 175 ksi proof stress against 150 ksi. See 2H vs 2HM.

Can 2H nuts be galvanized?

Yes. Galvanized nuts are tapped oversize so they still fit a galvanized stud, as 12-SAMSS-007 requires for galvanized nuts. Confirm your specification allows a galvanized finish.

How are 2H nuts marked?

With “2H” and the manufacturer’s identification mark on one face.

Related

B7 stud bolts

The stud that 2H nuts are made for.

A194 2HM nuts

Hardness-limited nuts for sour service.

Nut compatibility chart

Which nut goes with which bolt.

Need 2H nuts or B7 sets?

Send size, thread and quantity: we supply from stock or machine to order, with certificates.

Request a quote+966 54 614 8678