+966 54 614 8678 [email protected] WhatsApp
JTE FastenersBolting & hardware, Al Jubail العربية Request a quote

Flange isolation gasket kits for cathodic protection and dissimilar metals

Insulating gasket kits with sleeves and washers for every flange joint that must stop current flowing, supplied with matching stud bolts, plus spiral wound and ring joint gaskets, from Al Jubail.

A flange isolation kit electrically separates two flanges so that cathodic protection current, stray current or galvanic current cannot pass through the joint. The kit replaces the normal gasket with an insulating one and adds an insulating sleeve over every stud bolt and insulating washers under the nuts, so no metal path is left between the flanges. It is used at the boundary of a cathodically protected pipeline and where two different metals are bolted together.

Kit types
Type E (full face), Type F (raised face), Type D (ring joint groove), VCS sealing gasket kits
Gasket materials
Phenolic, neoprene-faced phenolic, G-10 / G-11 glass-reinforced epoxy (GRE), 316 stainless cored GRE
Seals
Nitrile, Viton (FKM) or spring-energised PTFE, to suit temperature and service
Sleeves and washers
G-10 or Mylar sleeves, G-10 insulating washers, plated steel washers
Sizes
ASME B16.5 and B16.47 flanges, Class 150 to 2500 depending on kit style
Also supplied
Spiral wound gaskets to ASME B16.20; R, RX and BX ring joint gaskets

Kit types explained

Type E
Full-face gasket with bolt holes; also keeps dirt out of the bore of the bolt holes
Type F
Fits inside the bolts on the raised face; located by the studs
Type D
Oval or octagonal insulating ring for ring-joint flanges
VCS / sealing kits
Stainless-cored GRE gasket with a seal, for higher pressure joints
Double washer sets
Insulating and steel washers on both sides isolate the bolts from both flanges

Isolation kit materials and limits

The retainer and seal materials set the temperature limit of the kit. Ratings vary between manufacturers, so the selected kit’s datasheet is always quoted with the offer.

Typical insulating kit materials
ComponentMaterialTypical use and limits
Gasket retainerPlain phenolicLow pressure water and gas; lower temperature limit than GRE
Gasket retainerG-10 glass-reinforced epoxyStandard for oil and gas; temperature rating per manufacturer, commonly 120 °C to 150 °C
Gasket retainerG-11 glass-reinforced epoxyHigher temperature service, up to about 200 °C on some kits
SealNitrileHydrocarbons and water at moderate temperature
SealViton (FKM)Higher temperature and aggressive fluids
SealSpring-energised PTFEWide chemical resistance; Saudi Aramco limits spring-energised gaskets below 280 °F (138 °C)
SleevesG-10 or MylarFull-length sleeve over each stud bolt
WashersG-10 insulating plus zinc-plated or stainless steel washersUnder each nut, one or both sides

Material properties vary by kit and manufacturer; the selected product’s datasheet governs. G-7 retainers are not used with hydrocarbons.

Gaskets and ringsStud bolts

Spiral wound and ring joint gaskets

For flanges that are not isolated we supply standard gaskets to ASME B16.20 with the rings and filler the service needs.

Gasket rules commonly applied in Saudi plants
GasketRequirement
Spiral wound, outer ringRequired on all sizes (Saudi Aramco SAES-L-109)
Spiral wound, inner ringRequired on 24 in. and larger, Class 900 and above where applicable, PTFE filler and vacuum service (SAES-L-109)
Spiral wound windings316 stainless for general hydrocarbon and steam service; rings match the flange material
FillerGraphite for general service; PTFE not used in hydrocarbon or steam service
Ring joint gasketsOctagonal Type R to ASME B16.20 for RTJ and API 6A flanges; RX and BX where specified

Summarised from Saudi Aramco SAES-L-109 and ASME B16.20.

Saudi Arabia requirements for isolation kits

Saudi Aramco SAES-L-109 sets when insulating kits are used on flanged joints and how they fit with the cathodic protection standards.

Isolation kits in Saudi Aramco projects
RequirementWhat it means for the order
SAES-L-109, where kits are requiredApproved insulation kits (insulating gasket, sleeves and washers) are used at dissimilar-metal flanged joints with a high galvanic corrosion potential, and at insulating joints for cathodic protection.
SAES-L-109, where kits are not requiredFor example dry hydrocarbon gas in dry areas, temperatures above the non-metallic gasket limit, or flammable services where external bonding would make the kit ineffective.
Insulating jointsInsulating joints meet the mechanical requirements of SAES-L-109 and are installed as the cathodic protection or stray current protection standards require.
WashersFlat washers under nuts are required on insulating flanges.
Spring-energised sealsSpring-energised gaskets are not permitted at 280 °F (138 °C) and above, and only fire-safe gaskets are used in refineries and gas plants.
Vendor statusJTE Fasteners is ISO 9001 certified and registered as an approved vendor with Saudi Aramco and SABIC.

Summarised from Saudi Aramco SAES-L-109. The kit type and materials follow the project’s cathodic protection design; send the datasheet with the enquiry.

Where isolation kits are used

Any flange that sits on the boundary of a cathodic protection system, or joins two different metals, needs isolating.

Pipeline CP boundaries

Where a buried, cathodically protected pipeline enters a plant or station.

Dissimilar metal joints

Carbon steel to stainless, duplex, copper-nickel or titanium flanges.

Pump and equipment nozzles

Isolating equipment from a protected line.

Loading lines and jetties

Stray current protection on marine loading lines.

Kits with bolting

Sleeved stud bolts and nuts supplied with the kit.

Shutdown packs

Kits and gaskets tagged by joint for planned work.

Supplied ready to install

An isolation kit only works if every bolt is sleeved and every washer is in place. We supply complete sets.

  • Gasket, sleeves and washers counted per flange
  • Stud bolts and nuts in the right length for the kit thickness
  • Kits packed and labelled per joint
  • Datasheet with temperature and pressure ratings

Stud bolts

Documents with every order

Kits are traceable to the manufacturer’s material and test data.

  • Manufacturer’s datasheet and certificate
  • Material certificates for steel washers and studs
  • EN 10204 3.1 MTC for bolting
  • Packing list per joint

Quality and certificates

Flange isolation kit questions

What is in a flange isolation kit?

An insulating gasket, a full-length insulating sleeve for each stud bolt, and for each bolt two insulating washers and two steel washers in a double-washer set. Together they stop any metal-to-metal contact between the two flanges.

What is the difference between Type E and Type F kits?

A Type E gasket is full face, the same outside diameter as the flange with bolt holes. A Type F gasket sits inside the bolt circle on the raised face and is located by the studs. Type D is an insulating ring for ring-joint flanges.

When does Saudi Aramco require isolation kits?

SAES-L-109 calls for approved insulation kits at dissimilar-metal flanged joints with high galvanic corrosion potential and at insulating joints for cathodic protection, with some exceptions such as dry hydrocarbon gas in dry areas.

What temperature can a G-10 isolation kit take?

It depends on the manufacturer and seal. G-10 retainers are commonly rated from about 120 °C to 150 °C, and G-11 to about 200 °C. We quote the selected kit’s datasheet rating for your service.

Why use a single-washer kit underground?

On buried flanges a single-washer set lets cathodic protection current reach the bolts and nuts on one side, protecting them from corrosion, while the joint stays isolated.

Do you supply the stud bolts for isolation kits?

Yes. Insulating gaskets and washers add thickness, so we supply stud bolts at the correct length with the kit, in B7, B7M or coated bolting as the line class requires.

Updated

Related

Gaskets and rings

Spiral wound, RTJ and soft gaskets.

Stud bolts

B7, B7M, L7 and coated studs.

Flanges

ASME B16.5 and B16.47 flanges.

Need isolation kits?

Send the flange sizes, classes, faces and service: we quote complete kits with stud bolts.

Request a quote+966 54 614 8678