+966 54 614 8678 [email protected] WhatsApp
JTE FastenersBolting & hardware, Al Jubail العربية Request a quote

Shear connectors and weld studs for drawn-arc stud welding

Headed shear connectors for composite steel and concrete construction and threaded weld studs for embed plates and equipment, to ISO 13918 or AWS D1.1, supplied with the matching ceramic ferrules.

A shear connector is a headed steel stud welded to a steel beam so that the concrete slab above acts together with the beam. They are welded by the drawn-arc process: the stud is lifted to draw an arc, plunged into the molten pool, and a ceramic ferrule shapes the weld. ISO 13918 covers the studs and ferrules, with type SD for headed shear connectors, and AWS D1.1 Type B headed studs have a 65 ksi (450 MPa) minimum tensile strength. Carbon steel studs are cold-finished low-carbon bar to ASTM A108, grades 1010 to 1020.

Standards
ISO 13918:2017 + A1:2021; AWS D1.1 Clause 9 (stud welding)
Shear connectors
ISO 13918 type SD; AWS D1.1 Type B headed studs
Threaded studs
ISO 13918 types PD (partly threaded) and RD (reduced shaft)
Material
ASTM A108 cold-finished steel, grades 1010 to 1020; stainless on request
Diameters
Shear connectors 16, 19, 22 and 25 mm; 3/4 and 7/8 in.
Ferrules
Ceramic ferrules matched to stud diameter and base
Workers on a reinforced concrete deck during construction
Concrete deck under construction (photo for illustration)

What we supply

Shear connectors
Headed studs for composite beams and decks
Threaded studs
PD and RD studs for embed plates and brackets
Ceramic ferrules
Flat, vertical and through-deck ferrules
Mixed orders
Studs packed by diameter and length per area

AWS D1.1 stud types

AWS D1.1 sorts weld studs by use. Type B is the headed stud used as a shear connector and concrete anchor.

AWS D1.1 weld stud types and minimum properties
TypeUseTensile minYield minElongation min (2 in.)
Type AGeneral purpose, not shear transfer61 ksi (420 MPa)49 ksi (340 MPa)17%
Type BHeaded shear connectors and concrete anchors65 ksi (450 MPa)51 ksi (350 MPa)20%

Values summarised from AWS D1.1 as published by stud manufacturers. Types C (deformed bar anchors) and D (added in D1.1:2025) are not shown. Stud size, spacing and capacity are designed by the structural engineer.

Structural boltsAnchor bolts

ISO 13918 drawn-arc stud types

ISO 13918 identifies each stud type by a letter code, for example SD for headed shear connectors. The types below are drawn-arc studs, welded with a ceramic ferrule.

Common ISO 13918 drawn-arc studs
TypeDescriptionTypical use
SDHeaded shear connectorComposite beams, decks and bridges
PDPartly threaded studBolting brackets and equipment to steel
RDThreaded stud with reduced shaftThreaded fixings on embed plates
UDUnthreaded studPins and anchors

Shear connectors are commonly 16, 19, 22 or 25 mm, with 19 mm the usual size for welding through steel decking.

Saudi Arabia requirements for shear connectors

Saudi Aramco covers shear connectors in its structural steel standard 12-SAMSS-007. The first point is from an unofficial copy of the 2011 issue, the second compares it with the current AWS clause, and the third is a general welding rule; confirm against the current revision.

Shear connectors on Saudi Aramco projects
RequirementWhat it means for the order
Headed studs (12-SAMSS-007, 2011 copy)Shear connectors for composite construction are headed studs to ASTM A108 grades 1010 to 1020, AWS D1.1 Type B.
Welding codeThe 2011 copy of 12-SAMSS-007 cites AWS D1.1 Section 7; in AWS D1.1:2020 and later, stud welding is Clause 9.
Qualification (AWS D1.1 / ISO 14555, not a 12-SAMSS-007 clause)Welding procedure and stud qualification are the fabricator’s responsibility under AWS D1.1 or ISO 14555.

Based on an unofficial copy of 12-SAMSS-007 (2011), which may be superseded; confirm against the current revision in your project specification. JTE supplies studs and ferrules; welding is done by the steel fabricator or erector.

Where weld studs are used

Drawn-arc studs are the structural stud welding process, from composite decks to embed plates.

Composite floors

Shear connectors on beams under concrete slabs.

Embed plates

Headed studs anchoring plates into concrete.

Bridges

Shear connectors on steel girders.

Threaded fixings

PD and RD studs for brackets and supports.

Equipment

Studs for mounting equipment to steel.

Site packs

Studs and ferrules packed per area.

Studs and ferrules together

Every drawn-arc stud needs a ferrule matched to its diameter and base, so we supply both.

  • Flat ferrules for down-hand welding
  • Vertical ferrules for wall welding
  • Through-deck ferrules
  • Studs by diameter and length
  • Stainless studs on request

Structural steel

Documents with every order

Stud material and properties are certified for the fabricator’s records.

  • EN 10204 3.1 MTC
  • Mechanical test results
  • Dimensional check
  • Lot traceability
  • 3.2 with third-party inspection

Quality and certificates

Weld stud and shear connector questions

What is a shear connector?

A headed steel stud welded to the top of a steel beam so that the concrete slab and the beam act together as one composite section.

What is an AWS Type B stud?

A headed stud used for shear connectors and concrete anchorage, with a 65 ksi (450 MPa) minimum tensile strength, 51 ksi yield and 20% elongation.

What material are shear studs made from?

Cold-finished low-carbon steel bar to ASTM A108, grades 1010 to 1020. Stainless studs are used in some outdoor or marine settings.

Why do weld studs need ceramic ferrules?

In drawn-arc welding, the ferrule contains the molten metal, shapes the weld fillet and shields the arc. It is broken off and discarded after welding.

Do you weld the studs?

No. We supply studs and ferrules; welding and qualification are done by the steel fabricator or erector under AWS D1.1 or ISO 14555.

Updated

Related

Structural steel and bars

Plates, sections and bars.

F3125 structural bolts

A325 and A490 bolts for steel connections.

Anchor bolts

Cast-in anchor bolts for foundations.

Need shear connectors for a project?

Send the stud schedule: diameter, length and quantity per area. We quote studs and ferrules together.

Request a quote+966 54 614 8678