+966 54 614 8678 [email protected] WhatsApp
JTE FastenersBolting & hardware, Al Jubail العربية Request a quote

Nut compatibility chart: which nut goes with which bolt

Matching nuts for A193, A320 and A453 stud bolts, structural A325 and A490 bolts, anchor bolts and metric bolts, with the Saudi Aramco service ranges.

The nut must match the bolt. ASTM A193 B7 studs take A194 2H nuts, B7M takes 2HM, A320 L7 takes Grade 7 (or Grade 4), L7M takes 7M, B16 takes Grade 4 or 7, and B8 and B8M take Grade 8 and 8M. Structural A325 and A490 bolts take A563 DH nuts, and metric class 8.8, 10.9 and 12.9 bolts take class 8, 10 and 12 nuts. The tables below list each pair, with the Saudi Aramco SAES-L-109 service range where one applies.

Flange and pressure bolting

Stud bolt and nut pairs for flanges
Stud boltMatching nutService (Saudi Aramco SAES-L-109, Table 5)
ASTM A193 B7A194 2H (Grade 4 or 7 also compatible)General service, about −40 to 450 °C
ASTM A193 B7MA194 2HMWet sour service
ASTM A320 L7A194 Grade 7 or Grade 4, Charpy tested (7L / 4L)Low temperature, about −101 to 343 °C
ASTM A320 L7MA194 7MLow temperature to about −73 °C, including cold sour
ASTM A193 B16A194 Grade 4 (Grade 7 is the ASTM substitute)High temperature, about 450 to 645 °C
ASTM A193 B8 (Class 1 and 2)A194 Grade 8304 stainless service
ASTM A193 B8M (Class 1 and 2)A194 Grade 8M316 stainless service
ASTM A453 Grade 660A453 660 nuts, or as specifiedHigh-temperature turbine and casing bolting
Duplex and super duplexNuts of the same duplex or super duplex gradeSeawater and corrosion-resistant alloy service (SAES-L-109, 13.3)

Flange bolting normally uses no washers: SAES-L-109 section 13.4.1 calls for flat washers only in special cases such as insulating and plastic flanges.

Structural and anchor bolting

Structural and anchor bolt hardware
BoltNutWasherSource
ASTM A325 / F3125 Grade A325, Type 1A563 DH (A563M 10S)F436Saudi Aramco 12-SAMSS-007, 4.6
ASTM A490 / F3125 Grade A490A563 DHF436Saudi Aramco 12-SAMSS-007, 4.6
ASTM A307 Grade AA563 Grade A, heavy hexF436Saudi Aramco 12-SAMSS-007, 4.7
ASTM F1554 Grade 36 / A36 rodA563 Grade A (hex to 1-1/2″, heavy hex above)F436, one per anchor bolt12-SAMSS-007, 4.8 and 6.2.5.21
ASTM A193 B7 or F1554 Grade 105 (high-strength anchors)A194 or A563 DHF43612-SAMSS-007, 4.9

Metric bolts

Metric bolt and nut property classes
Bolt property classNut property classStandard
8.88ISO 898-1 / ISO 898-2
10.910ISO 898-1 / ISO 898-2
12.912ISO 898-1 / ISO 898-2
A2-70 (304 stainless)A2-70ISO 3506-1 / ISO 3506-2
A4-70 (316 stainless)A4-70ISO 3506-1 / ISO 3506-2
A4-80 (316 stainless)A4-80ISO 3506-1 / ISO 3506-2

A nut of a higher class can usually replace a lower one, but never where hardness is limited, as in sour service.

Three rules that prevent rejections

  • A harder nut is not always better: a 2H nut on a B7M stud breaks the 22 HRC hardness limit for sour service.
  • Cold service needs Charpy-tested nuts as well as studs: order Grade 7 or 4 with A194 supplementary requirement S3, marked 7L or 4L.
  • Galvanized nuts must be tapped oversize to fit a galvanized bolt, as 12-SAMSS-007 section 5.2.4 requires.

Nut compatibility questions

Can I use a 2H nut on a B7M stud?

No. B7M is used for sour service, where hardness is limited to 22 HRC. A 2H nut can be up to 38 HRC, so the matching nut is 2HM.

Which nuts are compatible with ASTM A193 B7?

A194 2H is the standard pair; A194 Grade 4 and Grade 7 nuts are also compatible. Saudi Aramco SAES-L-109 names 2H.

Which nut goes with A320 L7 in cold service?

A194 Grade 7 (or Grade 4) with supplementary requirement S3 Charpy testing, marked 7L or 4L.

Do flange stud bolts need washers?

Usually not. Saudi Aramco SAES-L-109 section 13.4.1 calls for flat washers only in special cases, such as insulating and plastic flanges.

Which nut goes with an A325 structural bolt?

ASTM A563 DH (or A563M 10S in metric), with an F436 hardened washer, as Saudi Aramco 12-SAMSS-007 specifies.

Which nut class goes with a 10.9 metric bolt?

Property class 10 to ISO 898-2.

Updated

Related

ASTM A194 nut grades

2H, 2HM, Grade 4, Grade 7 and 7M heavy hex nuts.

B7 vs B7M

When to use the sour-service grade.

Fastener grade markings

How to read marks on bolts and nuts.

Need studs with the right nuts?

Send the grade, size and service: we supply matched, certified sets.

Request a quote+966 54 614 8678