Spiral wound gaskets to ASME B16.20
Spiral wound gaskets for ASME B16.5 and B16.47 flanges, with stainless windings, graphite or other fillers and centering and inner rings, supplied from Al Jubail together with the stud bolts for the same joints.
A spiral wound gasket is a V-shaped metal strip wound together with a soft filler, held between a centering ring and, where needed, an inner ring. The metal winding acts as a spring and the filler makes the seal. ASME B16.20 sets the dimensions, materials, marking and colour code for gaskets that fit ASME B16.5 and B16.47 flanges. Standard gaskets have a 4.5 mm (0.175 in.) winding with rings of about 3 mm (0.117 to 0.131 in.).
- Standard
- ASME B16.20 (current edition 2023)
- Flanges
- ASME B16.5 NPS 1/2 to 24 (Class 2500 to NPS 12); ASME B16.47 Series A and Series B
- Windings
- 316L and 304 stainless as standard; 321, 347, alloy 625, 825 and others on request
- Fillers
- Flexible graphite, PTFE, vermiculite or mica, chosen by temperature and service
- Rings
- Ring material normally to the flange material or project spec (Aramco: matched to the flange); inner ring commonly stainless
- Thickness
- 4.5 mm (0.175 in.) winding; rings approx. 3 mm (0.117 to 0.131 in.)

What we supply
- Outer ring (CG type)
- Winding with centering ring, for raised-face flanges
- Inner and outer ring (CGI type)
- Winding with centering and inner rings
- Large diameter
- Gaskets for ASME B16.47 Series A and B flanges
- Joint kits
- Gaskets packed with the matching stud bolts and nuts per flange
Choosing filler and rings
The filler sets the temperature limit; the flange class, size and filler decide whether an inner ring is needed. Manufacturer limits are shown; project specifications may be stricter.
| Item | Detail | Colour code |
|---|---|---|
| Flexible graphite filler | General hydrocarbon, steam and chemical service; about -240 to 450 °C by maker (425 °C max in SAES-L-109 Table 4, unofficial 2018 copy) | Grey stripe |
| PTFE filler | Chemical service at lower temperature, about -180 to 260 °C; inner ring always required | White stripe |
| Vermiculite filler | High-temperature and oxidising service | Per maker |
| 316L winding | Standard winding for refinery and petrochemical service | Green ring edge |
| 304 winding | General service where 304 is acceptable | Yellow ring edge |
| Inner ring by class | All fillers: NPS 24 and up in Class 900, NPS 12 and up in Class 1500, NPS 4 and up in Class 2500 | – |
| Inner ring by filler | Always with PTFE; with flexible graphite unless the buyer specifies otherwise | – |
Temperature limits are manufacturer figures and vary by product. Ring rules are those reported by gasket makers for ASME B16.20; the colour code is shown on the edge of the centering ring.
Saudi Arabia requirements for spiral wound gaskets
Saudi Aramco sets gasket selection in SAES-L-109. The points below are from an unofficial copy of the 2018 issue; always confirm against the current revision named in your project specification.
| Requirement | What it means for the order |
|---|---|
| Standard | Spiral wound gaskets are made to ASME B16.20. |
| Winding | 316 stainless windings for general hydrocarbon and steam service. |
| Filler | High-purity flexible graphite in hydrocarbon or steam service; PTFE is not used in those services. |
| Outer ring | Required for all pipe sizes. |
| Inner ring | Required for 24 in. and larger, Class 900 and above where applicable, PTFE filler and vacuum service. |
| Ring material | Inner and outer ring material matched to the flange material. |
Based on an unofficial copy of SAES-L-109 (29 January 2018), which may be superseded; confirm against the current revision in your project specification. Your line class or data sheet is the final word.
Where spiral wound gaskets are used
The default gasket for raised-face flanges in refinery, petrochemical and utility piping.
Process piping
Raised-face ASME B16.5 flanges, Class 150 to 2500.
Equipment nozzles
Pumps, exchangers, vessels and valves.
Steam and utilities
Graphite-filled gaskets for steam and hot water.
Corrosive service
Alloy windings and inner rings to suit the fluid.
Shutdowns
Gaskets and studs packed per joint for turnarounds.
Large flanges
ASME B16.47 Series A and B for big-bore lines.
Supplied with the bolting
One order covers the gasket and everything that clamps it.
- A193 B7 and B7M stud bolts
- A194 2H and 2HM nuts
- PTFE coated studs
- Flange isolation kits
- Packed and tagged per joint
Documents with every order
Gasket paperwork is checked against the line class before dispatch.
- Manufacturer’s certificate of conformity
- Material certificates for rings
- Marking check against B16.20
- Packing list per joint
- Third-party inspection on request
Spiral wound gasket questions
When does a spiral wound gasket need an inner ring?
Gasket makers report that ASME B16.20 requires inner rings with PTFE filler, with flexible graphite unless the buyer specifies otherwise, and for all fillers at NPS 24 and up in Class 900, NPS 12 and up in Class 1500 and NPS 4 and up in Class 2500. The 2018 issue (unofficial copy) of Saudi Aramco SAES-L-109 adds vacuum service and sizes 24 in. and larger.
What do the colours on a spiral wound gasket mean?
The edge of the centering ring is painted to show the winding metal, for example green for 316L and yellow for 304, and stripes show the filler, grey for flexible graphite and white for PTFE.
How thick is a spiral wound gasket?
A standard ASME B16.20 gasket has a 4.5 mm (0.175 in.) winding and rings of about 3 mm (0.117 to 0.131 in.).
Can a spiral wound gasket be reused?
No. Once compressed, the winding does not recover fully, so fit a new gasket whenever the joint is opened.
Can PTFE-filled gaskets be used in hydrocarbon service on Aramco projects?
No. The 2018 issue (unofficial copy) of SAES-L-109 says fillers such as PTFE that deteriorate at high temperature shall not be used in hydrocarbon or steam service.
Updated
Related
Ring type joint gaskets
R, RX and BX rings for RTJ flanges.
Flange isolation kits
Insulating gasket kits for cathodic protection.
Stud bolts
A193 B7, B7M, B16 and stainless flange studs.
Need gaskets for a flange list?
Send the line list or joint schedule: we quote gaskets, stud bolts and nuts together.