+966 54 614 8678 [email protected] WhatsApp
JTE FastenersBolting & hardware, Al Jubail العربية Request a quote

ASTM A193 B8M Class 2 stud bolts: strain-hardened 316 stainless

Higher-strength 316 stainless steel studs with A194 8M nuts for corrosive service where Class 1 stainless cannot hold enough load on the gasket, supplied from Al Jubail with strength confirmed by diameter.

B8M Class 2 is 316 stainless steel bolting that has been carbide solution treated and then strain hardened by cold working. The cold work lifts the minimum yield from 30 ksi for Class 1 to between 50 and 95 ksi depending on diameter, so a stainless joint can be tightened enough to seat the gasket. The strength gain is largest on small studs and falls away as the diameter grows, and the standard tables stop at 1-1/2 inch.

Stud
ASTM A193 Grade B8M Class 2 (Type 316 stainless, strain hardened)
Nut
ASTM A194 Grade 8M; strain-hardened 8M where the proof load is needed
Max hardness
321 HB (35 HRC)
Min yield
95 ksi at 3/4 in. and under, falling to 50 ksi at 1-3/8 to 1-1/2 in.
Size range
Up to 1-1/2 in. (M36); larger studs are supplied as Class 1 or another grade
Documents
EN 10204 3.1 MTC with tensile, yield and hardness results

B8M classes compared

Class 1
Carbide solution treated; 75 ksi tensile, 30 ksi yield at all sizes; max 223 HB
Class 1A (B8MA)
Solution treated after threading for best corrosion resistance; 75 / 30 ksi; max 192 HB
Class 2
Solution treated then strain hardened; 90 to 110 ksi tensile and 50 to 95 ksi yield by size; max 321 HB

B8M Class 2 strength by diameter

Strain hardening only penetrates part of the way into the bar, so ASTM A193 sets lower minimums for each larger diameter band. Always check the band for the stud size, not the headline value.

ASTM A193 B8M Class 2 minimum properties
DiameterMin tensileMin yieldElongation / reduction of area
3/4 in. and under (up to M20)110 ksi (760 MPa)95 ksi (655 MPa)15% / 45%
7/8 to 1 in. (over M20 to M24)100 ksi (690 MPa)80 ksi (550 MPa)20% / 45%
1-1/8 to 1-1/4 in. (over M24 to M30)95 ksi (655 MPa)65 ksi (450 MPa)25% / 45%
1-3/8 to 1-1/2 in. (over M30 to M36)90 ksi (620 MPa)50 ksi (345 MPa)30% / 45%
B8M Class 1, all sizes (for comparison)75 ksi (515 MPa)30 ksi (205 MPa)30% / 50%

Values from ASTM A193 Table 3. B8M Class 2 is lower than B8 (304) Class 2 in every size band, so B8 figures must not be used for B8M. Maximum hardness for all Class 2 sizes is 321 HB / 35 HRC.

B8 and B8M stud boltsNut compatibility chart

When to choose Class 2, and when not to

Class 2 solves one problem, gasket seating with stainless bolting, and brings limitations with it.

B8M Class 2 selection guide
SituationGuidance
Stainless bolting must seat a spiral wound or metal gasketClass 2 gives several times the yield of Class 1 on small and medium studs; the joint calculation should still be checked.
Large studs over 1-1/2 in.Class 2 is not tabulated; use another grade (for example B7 with coating, duplex or a nickel alloy) as the line class allows.
Wet sour (H2S) serviceISO 15156-3 accepts austenitic stainless only when free of cold work intended to raise strength and at 22 HRC maximum. Strain-hardened Class 2 does not meet that route; B8M Class 1 or 1A is used instead, within its environmental limits.
Best corrosion resistance at the threadsClass 1A (B8MA) is solution treated after threading and is the choice where corrosion resistance matters more than strength.
High-temperature serviceCheck the design code’s allowable stress for strain-hardened material at the design temperature; A453 Grade 660 is the usual high-temperature stainless bolting.

Guidance summarised from ASTM A193, ASTM A194 and ISO 15156-3 Table A.2. The project material selection decides.

Saudi Arabia requirements for stainless bolting

Saudi Aramco SAES-L-109 lists alloy steel stud bolts (B7, B7M, L7, L7M, B16) for process piping. Stainless B8M bolting appears where a project’s material selection calls for it, mostly in corrosive or offshore environments.

B8M Class 2 in Saudi projects
RequirementWhat it means for the order
Saudi Aramco SAES-L-109, aggressive external environmentsCorrosion-resistant alloy bolting is one of the permitted options for offshore and underground bolting, alongside ceramic-fluoropolymer coated B7 to 09-SAMSS-107.
Line class or datasheetThe class (1, 1A or 2) must be stated. A193 treats B8M as Class 1 unless Class 2 is ordered, so an order that only says B8M is quoted as Class 1.
Wet sour linesStrain-hardened Class 2 is not supplied for wet sour service; B8M Class 1 or 1A at 22 HRC maximum, or B7M / L7M per SAES-L-109, is offered instead.
DocumentsEN 10204 3.1 MTC with tensile, yield and hardness for the actual diameter supplied; PMI on request.
Vendor statusJTE Fasteners is ISO 9001 certified and registered as an approved vendor with Saudi Aramco and SABIC.

Summarised from Saudi Aramco SAES-L-109 and ISO 15156-3. Project specifications take precedence; send them with the enquiry.

Where B8M Class 2 studs are used

Class 2 is used on stainless and corrosive-service flanges where the bolt has to carry real gasket load.

Stainless process piping

Flanges on 316 piping in chemical and water treatment units where carbon steel bolts would rust.

Spiral wound gasket joints

Joints that need more bolt load than Class 1 stainless can give.

Pumps and valves

Body and bonnet bolting on stainless equipment in corrosive service.

Coastal and offshore structures

Exposed flanges in marine air where coated carbon steel would be replaced often.

Shutdown replacements

Matching Class 2 studs and nuts tagged by joint for planned shutdowns.

Class traceability

Class 1 and Class 2 kept apart and identified on the certificate.

Keeping Class 1 and Class 2 apart

Class 1 and Class 2 studs look identical. Mixing them puts a soft stud into a joint designed for a strong one.

  • Class stated on every label and certificate
  • Separate storage by class
  • Hardness checked on each lot
  • Nuts matched to the stud class

Stud bolts

Documents with every order

Because Class 2 strength depends on diameter, the certificate reports results for the size actually supplied.

  • EN 10204 3.1 MTC
  • Tensile and yield for the supplied diameter
  • Hardness results
  • Heat number traceability
  • 3.2 with third-party inspection

Quality and certificates

B8M Class 2 stud bolt questions

What is the difference between B8M Class 1 and Class 2?

Both are Type 316 stainless steel. Class 1 is carbide solution treated only and has a 30 ksi minimum yield at every size. Class 2 is solution treated and then strain hardened, which raises the minimum yield to between 50 and 95 ksi depending on diameter.

Why does B8M Class 2 get weaker as the diameter increases?

Strain hardening comes from cold working the bar, and the effect penetrates only part of the way into the section. Larger bars harden less through their thickness, so ASTM A193 sets lower minimums for each larger size band and stops at 1-1/2 inch.

Which nut goes with a B8M Class 2 stud?

An ASTM A194 Grade 8M nut. Where the joint needs the higher proof load, strain-hardened Grade 8M nuts are specified; A194 gives separate proof loads for them.

Can B8M Class 2 be used in sour service?

Not under the general route for austenitic stainless in ISO 15156-3, which requires material free of cold work intended to raise strength and a maximum of 22 HRC. B8M Class 1 or 1A, or B7M and L7M per Saudi Aramco SAES-L-109, are used instead.

If my order just says B8M, what will I receive?

ASTM A193 treats B8 and B8M as Class 1 unless another class is specified. We quote Class 1 unless the order or line class says Class 2.

Is B8M Class 2 the same strength as B7?

No. B7 has a 105 ksi minimum yield up to 2-1/2 inch, while B8M Class 2 is 95 ksi at 3/4 inch and under and falls to 50 ksi at 1-1/2 inch. The joint design must use the B8M Class 2 values for the actual size.

Updated

Related

B8 and B8M stud bolts

304 and 316 stainless studs, Class 1 and 1A.

Nickel alloy fasteners

Inconel, Monel and Hastelloy for seawater and acid service.

Duplex stud bolts

Higher strength and chloride resistance than 316.

Need B8M Class 2 studs?

Send the sizes, lengths and line class: we confirm the strength band for each diameter with the quote.

Request a quote+966 54 614 8678