Spectacle blinds, paddle blanks and paddle spacers to ASME B16.48
Figure-8 spectacle blinds, paddle blanks and ring spacers for positive isolation and pressure testing of flanged piping. We supply them from Al Jubail with the longer studs and gaskets each blinded joint needs.
A spectacle blind is a figure-8 plate with one solid and one open end, fitted between two flanges to close or open a line. Rotating it 180 degrees switches the line between positive isolation and normal flow. ASME B16.48 covers spectacle blinds, paddle blanks and paddle spacers from NPS 1/2 to 24 in Classes 150 to 2500. Larger sizes are designed to ASME B31.3. We supply them from established manufacturers, with 3.1 certificates and the longer studs the joint needs.
- Standard
- ASME B16.48 Line Blanks (2025 is the latest edition listed); larger sizes designed to ASME B31.3
- Types
- Figure-8 (spectacle) blanks, paddle blanks (spades), paddle spacers (ring spacers)
- Sizes
- NPS 1/2 to 24 in B16.48; NPS 26 and larger to a drawing or calculation
- Classes
- 150, 300, 600, 900, 1500 and 2500
- Facings
- Flat or raised face for RF flanges; female or male ring joint for RTJ flanges
- Materials
- A516 Gr 70, A105, A350 LF2, A240 or A182 316L, Cr-Mo and other grades to order
- Documents
- EN 10204 3.1 certificates; third-party inspection on request
- Bolting
- Longer stud bolts cut and threaded in our factory in Al-Jubail

What we supply
- Spectacle (figure-8) blinds
- One-piece blank and spacer joined by a web, NPS 1/2 to 24
- Paddle blanks and spacers
- Separate plates with handles for large, heavy or crowded joints
- RTJ figure-8 blanks
- Female (grooved) or male (ring) faces for ring-joint flanges
- Large-bore blanks
- NPS 26 and larger to the buyer’s drawing or B31.3 calculation
- Hydrotest blinds
- Temporary blanks for system pressure tests, rated to your test pressure
- Joint sets
- Longer stud bolts, nuts and gaskets packed for each blinded joint
ASME B16.48 blank thickness by class and size
B16.48 sets one thickness, t, for each size and class. The same t applies to the figure-8 blank, the paddle blank and the paddle spacer for raised-face flanges.
| NPS | Class 150 | Class 300 | Class 600 | Class 900 | Class 1500 | Class 2500 |
|---|---|---|---|---|---|---|
| 1/2 | 3.0 | 6.4 | 6.4 | 6.4 | 6.4 | 9.7 |
| 3/4 | 3.0 | 6.4 | 6.4 | 6.4 | 9.7 | 9.7 |
| 1 | 3.0 | 6.4 | 6.4 | 6.4 | 9.7 | 9.7 |
| 1 1/2 | 6.4 | 6.4 | 9.7 | 9.7 | 12.7 | 15.7 |
| 2 | 6.4 | 9.7 | 9.7 | 12.7 | 12.7 | 15.7 |
| 3 | 6.4 | 9.7 | 12.7 | 15.7 | 19.1 | 22.4 |
| 4 | 9.7 | 12.7 | 15.7 | 19.1 | 22.4 | 28.4 |
| 6 | 12.7 | 15.7 | 22.4 | 25.4 | 35.1 | 41.1 |
| 8 | 12.7 | 22.4 | 28.4 | 35.1 | 41.1 | 53.8 |
| 10 | 15.7 | 25.4 | 35.1 | 41.1 | 50.8 | 66.5 |
| 12 | 19.1 | 28.4 | 41.1 | 47.8 | 60.5 | 79.2 |
| 14 | 19.1 | 31.8 | 44.5 | 53.8 | 66.5 | not listed |
| 16 | 22.4 | 38.1 | 50.8 | 60.5 | 76.2 | not listed |
| 18 | 25.4 | 41.1 | 53.8 | 66.5 | 85.9 | not listed |
| 20 | 28.4 | 44.5 | 63.5 | 73.2 | 95.3 | not listed |
| 24 | 31.8 | 50.8 | 73.2 | 88.9 | 111.3 | not listed |
Values as published from ASME B16.48 Tables 1 to 6; Class 2500 stops at NPS 12. Tolerance is minus zero, plus 3.0 mm up to NPS 18 and plus 4.8 mm from NPS 20. A raised face, if ordered, is added to t. Ring-joint figure-8 blanks have their own tables. Inch and metric tables are not exact equivalents, so do not mix them. Confirm against the edition named in your order.
Spectacle blind, paddle blank or line blind?
All of these devices close a line, but they differ in weight, space needed and how often the joint can be changed.
| Option | How it works | Best for | Watch for |
|---|---|---|---|
| Spectacle (figure-8) blind | Blank and spacer in one plate; rotate 180 degrees on the bolts | Joints isolated often; small and medium sizes | Weight and swing clearance at large sizes; the web sits outside the flange |
| Paddle blank and paddle spacer | Two loose plates swapped in the joint | Large or heavy joints; joints opened rarely; crowded piping | The spare plate must be stored, tagged and found when needed |
| Line blind or swing blind | Hinged, cam-operated or slide-operated assembly | Joints changed several times a year | Engineered item; check rating, maintenance and space |
| Blind flange | Bolted cover on an open flange end | Permanent line ends and future tie-ins | Not between two flanges; rated as a B16.5 or B16.47 flange |
| Spool removal | A pipe spool is taken out and the open ends are blanked | Highest-confidence positive isolation | Needs lifting, storage and blind flanges for both ends |
Spectacle blinds in Saudi Arabia: Aramco and site requirements
On Saudi Aramco piping, SAES-L-109 calls for spectacle plates or blanks and spacers at flanged joints and ties their design to standard drawings. The points below come from an unofficial copy; your project specification decides.
| Requirement | What it means |
|---|---|
| Provision at flanged joints | SAES-L-109 para. 11.1 asks the piping design to provide for spectacle plates, or blanks and spacers, for pressure testing, repairs, inspection and positive product segregation. |
| Thickness basis | Para. 11.2 sets the design thickness of all spectacle blinds and blanks by ASME B31.3. |
| Standard drawings | Spectacle plates follow the Aramco standard drawings in Table 3, for example AD-036633-001 for Class 150 RF flanges. ASME B16.48 is used for unlisted spectacle plates and blanks. |
| Gasket seat finish | Para. 11.3 requires the gasket seat finish of the flange dimensional standard: ASME B16.5, B16.47 or API 6A. |
| Jackscrews | Para. 5.6 calls for jackscrews to ease flange separation for maintenance, unless flange separators are used. |
| Sour service | Where the line class is sour, plates and welds must meet the hardness limits it calls up, such as NACE MR0175/ISO 15156. Check the MTC. |
| Coastal climate | Chlorides, sand and heat in Jubail Industrial City and Ras Tanura attack bare plate. Keep faces coated and capped until fitting. |
Based on an unofficial copy of SAES-L-109 (29 January 2018), which may be superseded; confirm against the current revision in your project specification. SABIC and other owners’ projects follow their own line classes, so check your project specification.
Where spectacle blinds and line blanks are used
Any flanged joint that must sometimes be closed with certainty is a candidate for a line blank.
Shutdowns and turnarounds
Blinding vessels, exchangers and columns before entry or hot work.
Hydrostatic testing
Separating new piping from live plant during system pressure tests.
Confined-space entry
Positive isolation of every line into a tank or vessel before entry.
Product segregation
Keeping two products or services apart at a manifold or tie-in.
Equipment maintenance
Isolating pumps, compressors and control valves at their flanges.
Tie-ins and future connections
Spacers that hold the gap for a later blank or a new branch.
Bolting for the blinded joint
A blank or spacer adds a plate and a second gasket to the joint, so standard flange studs are too short.
- Studs cut to the blinded length
- A193 B7, B7M, L7 or B8M
- 2H, 2HM, 4 or 8M nuts
- Spiral wound or RTJ gaskets
- Packed and tagged per joint
Documents with every order
Each plate is traced to its heat by the stamped marking and the certificate.
- EN 10204 3.1 MTC
- B16.48 marking on web or handle
- Dimensional report
- Hardness for sour service
- Third-party inspection on request
The three B16.48 line blank types
ASME B16.48 names three operating line blanks: the figure-8 blank, the paddle blank and the paddle spacer. Plant drawings use many other names for the same parts.
A figure-8 blank is better known as a spectacle blind. B16.48 defines it as a pressure-retaining plate with one solid end and one open end. A web, or tie bar, joins the two ends.
Figure-8 (spectacle) blind
The spectacle blind stays in the joint all the time. With the open ring in line, product flows. Loosen the studs, swing the plate 180 degrees, and the solid disc blocks the bore.
The part of the plate outside the flanges shows the line’s state at a glance. If the ring shows, the line is blocked; if the solid disc shows, the line is open.
Paddle blank (spade)
A paddle blank is the solid end of a figure-8 blank with a plain radial handle. It is also called a spade, a slip blind or a line blank. OSHA’s confined-space rule also uses the term skillet blind.
Paddle blanks are used where a one-piece spectacle would be too heavy, or where the joint is opened only rarely.
Paddle spacer (ring spacer)
A paddle spacer is the open end of a figure-8 blank with a plain radial handle. It fills the gap while the line is in service, so the flanges need not be pulled together.
Blank and spacer have the same thickness in B16.48. Swapping one for the other therefore keeps the same stud length and flange gap.
What ASME B16.48 covers
ASME B16.48 covers pressure-temperature ratings, materials, dimensions, tolerances, marking and testing of operating line blanks. Its scope is NPS 1/2 through NPS 24 for use between ASME B16.5 flanges in Classes 150 to 2500.
The standard first appeared in 1997 as Steel Line Blanks. New editions followed in 2005, 2010, 2015, 2020 and 2025, the latest one listed. Older purchase orders may still name an earlier edition, so state the edition you want.
| Topic | What the standard says |
|---|---|
| Sizes and classes | NPS 1/2 to 24; Classes 150, 300, 600, 900, 1500 and 2500 (Class 2500 tables stop at NPS 12) |
| Ratings | The same pressure-temperature ratings as ASME B16.5 flanges of the same material and class |
| Dimension tables | RF blanks for all three types; female and male ring-joint tables for figure-8 blanks |
| Thickness tolerance | Minus zero; plus 3.0 mm (0.12 in.) to NPS 18, plus 4.8 mm (0.19 in.) from NPS 20 |
| Handle or web | May be integral with the plate or attached to it |
| Marking | Steel stamped on the web or handle |
| Identification | Blank handles solid; spacer handles with one indicator hole of 12 mm (1/2 in.) minimum |
| Testing | Line blanks need no shop pressure test; system tests up to 1.5 times the 38 °C rating |
Facings, identification and marking
Choose the facing to suit the mating flanges. For raised-face flanges, the blank is normally flat on both sides and the gaskets seat on its faces.
B16.48 lets the buyer specify a raised face on the blank. The raised-face height is then added to t. A flat blank is the common, lower-cost default.
Ring-joint (RTJ) figure-8 blanks
For RTJ flanges, B16.48 gives two figure-8 designs. A female blank has a ring groove on each face, so a ring gasket sits on each side. A male blank has the ring shape machined on each face, to seat in the flange grooves.
B16.48 limits the groove side walls and the male ring surface to 1.6 µm (63 µin.) Ra. Quote the ring number with the order.
Telling a blank from a spacer
Once fitted, the plate is hidden between the flanges. B16.48 therefore requires a visible difference outside the joint.
Paddle blank handles are solid with no openings. Paddle spacer handles have a single through indicator hole near the end, at least 12 mm (1/2 in.) across. Some catalogs show other hole patterns; follow the standard.
Marking
B16.48 asks for stamping on the web or handle. The marks are the maker’s name or trademark, material and grade, pressure class, the B16 designation, size and ring number where relevant.
Some plants also paint handles by class or fit blind-list tags through the handle hole. These are site practices, not B16.48 rules, so state them on the order.
Materials for spectacle blinds
The blank should match the chemistry of the mating flanges and pipe. It must also be a plate or forging grade allowed by the piping code, usually ASME B31.3.
Carbon steel blanks are commonly cut from A516 Grade 70 plate or made from A105 forgings. Both fall in ASME B16.5 material group 1.1, the same group as A105 flanges.
Sour, cold and hot service
For sour service, the line class usually calls up NACE MR0175/ISO 15156 hardness limits. Ask for hardness results on the certificate.
For cold service, match the impact-tested flanges, for example A350 LF2. For hot service, check the upper temperature limit of the plate grade before you order.
| Material | Form | B16.5 group | Typical service |
|---|---|---|---|
| ASTM A516 Gr 70 | Plate | 1.1 | General carbon steel piping; B16.5 notes advise against use above 455 °C |
| ASTM A105 | Forging | 1.1 | General carbon steel piping with A105 flanges |
| ASTM A350 LF2 | Forging | 1.1 | Low-temperature service with impact-tested flanges |
| A516 Gr 70, normalized and Charpy tested | Plate | 1.1 | Low-temperature service where the line class allows plate |
| ASTM A240 316L / A182 F316L | Plate / forging | 2.3 | Corrosive and chloride-bearing services with 316L flanges |
| ASTM A182 F22 or F91 | Forging | Cr-Mo groups | High-temperature steam and hydrogen service |
Group numbers from ASME B16.5 as published; confirm the material list in the B16.48 edition you buy to. Duplex, nickel alloy and clad blanks are available to order.
Thickness, ratings and sizes above NPS 24
Inside its scope, B16.48 gives a blank the same pressure-temperature rating as a B16.5 flange of the same material group and class. A Class 300 blank in group 1.1 material is good for 51.1 bar at 38 °C, like the flange.
B16.48 stops at NPS 24. For NPS 26 and larger, blanks fit ASME B16.47 Series A or Series B flanges and are designed to a calculation.
The ASME B31.3 blank equation
ASME B31.3 para. 304.5.3 gives the minimum thickness of a permanent blank: t = dg x square root of (3P / 16SEW), plus c.
Here dg is the gasket inside diameter for raised or flat faces, or the gasket pitch diameter for ring joints. P is design pressure, S the allowable stress, E the quality factor, W the weld strength factor and c the corrosion and mechanical allowance.
Worked illustration
Assume dg = 30.0 in. and P = 285 psig. Take S = 23,300 psi for A516 Gr 70 at ambient temperature, and E = W = 1. The result is 1.44 in. (36.5 mm) before c.
Add a 1.5 mm corrosion allowance and round up to available plate. This is an illustration only; the designer must use the real gasket, temperature and code values.
Published large-bore tables
Published tables for B16.47 Series A blanks run from NPS 26 to 60. One such table was calculated to B31.3 with a 1.5 mm allowance. For Class 150 it gives 39 mm at NPS 26 and 88 mm at NPS 60.
Treat such tables as typical. Large blanks are made to the buyer’s drawing, and the bolt circle must match the flange series.
Using blinds for positive isolation
A correctly rated blank gives positive isolation: the plant being worked on is fully separated from live process. Valves alone can pass product if a seat leaks.
OSHA 29 CFR 1910.146 defines blanking or blinding as closing a line with a solid plate, such as a spectacle blind or skillet blind. The plate must cover the bore and hold the line’s maximum pressure with no leakage.
UK HSE guidance HSG253 lists the positive methods as spool removal, or a spade with double or single block and bleed. It prefers spool removal where reasonably practicable, because it is easier to check.
- Isolate with valves first, then vent and drain the section to be blinded, as HSG253 advises.
- Prove the valve isolation holds before any bolt is loosened.
- Spread the flanges, using jackscrews where fitted, and turn or insert the blank.
- Fit new gaskets on both faces and tighten the studs to the joint procedure.
- Tag the blank and record it on the plant’s blind list.
- Reverse the steps to return to service, and sign off the blind list when every blank is out.
Blinds in pressure testing
Line blanks are often used to close off sections during hydrostatic tests. B16.48 does not require a shop pressure test of the blank itself.
It allows system tests up to 1.5 times the 38 °C rating, rounded up to the next 1 bar (25 psi) step. Testing at a higher pressure is the user’s responsibility under the governing code.
Worked example
A Class 150 group 1.1 blank is rated 19.6 bar at 38 °C. Then 1.5 x 19.6 = 29.4 bar, which rounds up to 30 bar.
For Class 300, 1.5 x 51.1 = 76.65 bar, which rounds up to 77 bar. If the test needs more, a thicker test blind is designed for the test pressure.
Test blinds on site
Plant procedures commonly keep a separate hydrotest blind list. Each temporary blind is tagged, sized for the test pressure and removed after the test.
Forgotten test blinds are a known cause of start-up problems. The blind list and handle tags are how they are found.
Installation: gaskets, stud length and clearance
A blinded joint has two gasket faces instead of one. Fit a new gasket on each side of the blank or spacer; reused gaskets are a common cause of leaks.
The blank’s outside diameter is slightly larger than the raised face. A correctly centered plate therefore does not touch the studs.
Why the studs must be longer
ASME B16.5 stud lengths assume one gasket between two flanges. A blank or spacer adds its thickness t plus one more gasket.
Add both to the standard stud length, then round up to the next stock length. For example, an NPS 8 Class 300 joint needs studs at least 22.4 mm plus one gasket longer.
Spectacle or paddle: stud length differs
A spectacle blind stays in the joint, so its longer studs are permanent. Swapping a paddle blank for its spacer of equal thickness keeps the stud length the same.
Inserting a blank into a joint that had no spacer is different. The flanges must be spread by t plus a gasket, so check pipe flexibility first.
Space to turn the plate
Rotating a spectacle blind needs clear space of roughly the disc diameter plus the web length. In tight racks, a paddle pair may be easier.
Published weights show why. A Class 150 NPS 4 spectacle is about 3 kg and an NPS 24 about 129 kg. A Class 1500 NPS 24 spectacle is nearly 900 kg.
Tightening
Tighten in a cross pattern to the torque or tension in the joint procedure. Re-check after any temperature cycle the procedure calls for.
Our torque wrench and bolt tensioner page lists the tools used on blinded joints.
Receiving inspection and common mistakes
Check every blank against the order before it goes to the rack. Most problems found on site come from ordering, not manufacture.
- Stamping on the web or handle shows maker, material, class, B16 marking, size and ring number.
- Thickness is not below the table value; plus tolerance is allowed, minus is not.
- Spacer handles have the indicator hole; blank handles are solid.
- Bolt holes or outer diameter match the flange standard and class, B16.5 or B16.47 Series A or B.
- Spacer bore matches the pipe bore, especially for heavy-wall schedules.
- Gasket faces are free of dents, weld spatter and radial scratches.
- Heat number on the plate matches the 3.1 certificate.
Common mistakes
Most errors come from treating a blank as a simple plate. These are the ones we see most.
- Ordering by flange class without checking material group and temperature.
- Using a Class 150 blank in a Class 300 line because the plate looked thick enough.
- Forgetting the second gasket and the longer studs.
- Ordering B16.5 bolt holes for a B16.47 Series B flange, or the reverse.
- Painting over the stamped marks, so the class can no longer be read.
- Leaving test blinds in after a hydrotest.
How to order spectacle blinds: RFQ checklist
A complete RFQ line lets us quote without questions. Give each item in this order.
Example: Spectacle blind, ASME B16.48, NPS 6, Class 300, RF flat face, A516 Gr 70, with longer A193 B7 studs and two spiral wound gaskets, 3.1 MTC.
- Type: spectacle blind, paddle blank, paddle spacer or a matched pair.
- Standard and edition: ASME B16.48 (state the year), a client drawing, or design to ASME B31.3.
- Size and class: NPS and pressure class; for NPS 26 and above, B16.47 Series A or B.
- Facing: flat, raised face, female RTJ or male RTJ with ring number.
- Material: plate or forging grade, plus impact or hardness tests if needed.
- Bore: spacer inside diameter or the pipe schedule.
- Corrosion allowance, design and test pressure for any non-standard blank.
- Handle marking, paint color or tag-hole needs from your site procedure.
- Bolting and gaskets: stud grade, nut grade, coating and gasket type for each joint.
- Documents: EN 10204 3.1 or 3.2, dimensional report and third-party inspection.
Spectacle blind questions
What is the difference between a spectacle blind and a paddle blank?
A spectacle blind is one plate with a solid disc and an open ring joined by a web. You rotate it to open or close the line. A paddle blank is a separate solid plate with a handle, used with a matching paddle spacer. Paddle pairs suit large, heavy or crowded joints. Spectacles suit joints that are switched often.
Which standard covers spectacle blinds?
ASME B16.48 Line Blanks covers figure-8 (spectacle) blanks, paddle blanks and paddle spacers. Its scope is NPS 1/2 to 24, Classes 150 to 2500, for use between ASME B16.5 flanges. It sets ratings, materials, dimensions, tolerances, marking and testing. Larger blanks are usually designed with the ASME B31.3 blank equation.
How do you tell a paddle blank from a paddle spacer once installed?
Look at the handle. Under ASME B16.48 a paddle blank handle is solid with no openings. A paddle spacer handle has one through indicator hole near its end, at least 12 mm (1/2 in.) in diameter. On a spectacle blind, the end showing outside the flanges tells you which end is in the line.
What thickness is a Class 150 spectacle blind?
It depends on size. In B16.48, a Class 150 blank for raised-face flanges is 3.0 mm at NPS 1/2 and 6.4 mm at NPS 2. It is 12.7 mm at NPS 6, 19.1 mm at NPS 12 and 31.8 mm at NPS 24. The tolerance is minus zero and plus 3.0 or 4.8 mm, depending on size.
Are spectacle blinds available above NPS 24?
Yes, but B16.48 stops at NPS 24. Larger blanks are made to a drawing for ASME B16.47 Series A or B flanges. The thickness is calculated with the ASME B31.3 blank equation, including corrosion allowance. Tell us the flange series, class, gasket and design pressure, and we source them from established manufacturers.
What material should a spectacle blind be?
Match the chemistry of the mating flanges and pipe. A516 Grade 70 plate and A105 forgings suit most carbon steel lines. A350 LF2 suits cold service. 316L plate or forgings suit 316L piping. Cr-Mo grades such as F22 or F91 suit hot service. Sour service usually adds NACE MR0175/ISO 15156 hardness limits.
Do I need longer stud bolts when a spectacle blind is installed?
Yes. Standard ASME B16.5 stud lengths assume one gasket between two flanges. A blind adds its own thickness and a second gasket. Add both to the standard length, then round up to the next stock length. We cut and thread these longer studs in our factory in Al-Jubail.
Can a spectacle blind be used for a hydrostatic test?
Yes. B16.48 allows system tests up to 1.5 times the blank’s 38 °C rating, rounded up to the next 1 bar or 25 psi. For a Class 150 group 1.1 blank that is 30 bar. Higher test pressures need a blind designed for the test, under the user’s responsibility and the governing code.
Is a closed valve enough instead of a blind?
Not where positive isolation is required. Valve seats can pass product. OSHA defines blanking as closing a line with a solid plate that holds full pressure without leakage. HSE guidance HSG253 treats spades and spool removal as positive isolation, inserted after a proven valve isolation.
Do spectacle blinds need a raised face?
Usually not. For raised-face flanges the blank is normally flat, and the gaskets seat on its faces. ASME B16.48 lets the buyer order a raised face on the blank, with its height added to the table thickness. A raised face adds machining and cost, so order it only if your specification asks for it.
What is the difference between female and male RTJ figure-8 blanks?
A female ring-joint blank has a groove on each face, so a ring gasket fits on each side. A male ring-joint blank has the ring shape machined on each face, to seat directly in the flange grooves. B16.48 has separate tables for each. Give the ring number with your order.
What do Saudi Aramco projects require for spectacle plates?
Saudi Aramco SAES-L-109 requires provision for spectacle plates or blanks and spacers at flanged joints. Their thickness follows ASME B31.3 and their design follows Aramco standard drawings, with B16.48 for unlisted items. Based on an unofficial copy of SAES-L-109 (29 January 2018), which may be superseded; confirm against the current revision in your project specification.
What certificates come with spectacle blinds?
We supply EN 10204 3.1 mill test certificates that trace each plate by heat number to its stamped marking. Dimensional reports and hardness results are available where the order asks for them. Third-party inspection and 3.2 certification can be arranged on request. JTE is ISO 9001 certified.
Does JTE manufacture spectacle blinds?
No. We supply spectacle blinds, paddle blanks and spacers sourced from established manufacturers, checked against your order. What we make in our factory in Al-Jubail is the bolting: longer stud bolts cut and threaded to the blinded joint length. We pack them with nuts and gaskets for each joint.
Updated
Related
Flanges
ASME B16.5 and B16.47 flanges the blanks fit between.
RTJ gaskets
Ring gaskets for ring-joint figure-8 blanks.
Torque wrenches and bolt tensioners
Tools for tightening blinded joints.
Send your blind list
Size, class, facing and material for each joint are enough. We quote the blanks, spacers, longer studs and gaskets together.