+966 54 614 8678 [email protected] WhatsApp
JTE FastenersBolting & hardware, Al Jubail العربية Request a quote

Ring type joint (RTJ) gaskets: R, RX and BX

Solid metal ring gaskets for RTJ flanges and wellhead equipment, in oval and octagonal Type R, pressure-energised RX and BX, supplied from Al Jubail with the stud bolts and nuts for each joint.

A ring type joint gasket is a solid metal ring that sits in a machined groove in both flange faces and seals by deforming slightly as the bolts are tightened. Because the ring must flow into the groove rather than damage it, it is made softer than the flange. ASME B16.20 covers Type R, RX and BX rings for ASME and API flanges, and API 6A covers rings for wellhead and tree equipment. Solid rings are used once and replaced whenever the joint is opened.

Standards
ASME B16.20 (2023) and API Spec 6A (21st edition) ring gaskets
Types
R oval and octagonal; RX pressure-energised; BX for API 6BX flanges
Materials
Soft iron, low-carbon steel, F5, 304, 316, 347, 410; alloy 625 and 825 on request
Flanges
ASME B16.5 and B16.47 Series A RTJ flanges; API 6B and 6BX
Finish
Soft iron and low-carbon steel rings normally zinc plated
Use
Single use: fit a new ring every time the joint is broken
Flanged pipeline joints and valve
Flanged pipeline joints (photo for illustration)

What we supply

Type R
Oval or octagonal rings by ring number
Type RX
Pressure-energised rings for the same grooves
Type BX
Rings for API 6BX high-pressure flanges
Joint sets
Rings with stud bolts and nuts packed per flange

RTJ ring materials and maximum hardness

The ring must be softer than the flange groove so that it deforms without marking the flange. These maximum hardness values are the ASME B16.20 limits (and API 6A limits where they apply), as quoted by ring makers.

Ring gasket materials, maximum hardness and identification
MaterialMax hardnessIdentificationTypical use
Soft iron90 HBDCarbon steel flanges, general service
Low-carbon steel120 HBSCarbon steel flanges
4-6% Cr 1/2% Mo (F5)130 HBF5Low-alloy steel flanges, hot service
304 stainless160 HBS304Stainless flanges
316 stainless160 HBS316Stainless flanges, corrosive service
347 stainless160 HBS347High-temperature stainless service
410 stainless170 HBS410Martensitic stainless service

Hardness limits summarised from ring manufacturers’ literature quoting ASME B16.20 and API 6A. Limits for nickel alloys, duplex and titanium differ between makers, so they are agreed per order. API 6A rings are sourced from API-licensed manufacturers, with the monogram where ordered; JTE is not an API licensee.

All gaskets and ringsStud bolts for RTJ flanges

R, RX and BX compared

R and RX fit the same octagonal groove, but the make-up distance between flanges differs. BX is a separate design for API 6BX flanges.

Ring type joint styles
StyleShapeFlangesNotes
R ovalOval cross-sectionASME B16.5, B16.47 Series A, API 6BOriginal design; also fits older round-bottom grooves
R octagonalOctagonal cross-sectionASME B16.5, B16.47 Series A, API 6BImproved design for flat-bottom grooves; oval and octagonal are interchangeable in octagonal grooves
RXPressure-energised, asymmetricSame grooves as RNot a one-for-one swap: make-up distance differs
BXPressure-energised with balance holeAPI 6BX, up to 20,000 psiNot interchangeable with R or RX

Saudi Arabia requirements for ring joint gaskets

Saudi Aramco sets gasket selection in SAES-L-109. The points below are from an unofficial copy of the 2018 issue; confirm against the current revision named in your project specification.

Ring joint gaskets in Saudi Aramco piping (SAES-L-109, unofficial 2018 copy)
RequirementWhat it means for the order
TypeOctagonal ring joint gaskets, Type R per ASME B16.20, for API 6A Type 6B flanges and ASME RTJ flanges.
MaterialSelected for the service conditions; soft iron or low-carbon steel rings may be used.
Corroded serviceRubber-coated ring joint gaskets may be used for severely corroded services.

Based on an unofficial copy of SAES-L-109 (29 January 2018), which may be superseded; confirm against the current revision in your project specification. RX and BX rings are supplied when the line class or equipment data sheet calls for them.

Where RTJ gaskets are used

Ring joints are used on RTJ-faced flanges in high-pressure and high-temperature service and on wellhead equipment.

High-pressure piping

RTJ flanges in high-pressure classes; R and RX rings cover ASME Class 150 to 2500.

Wellheads and trees

API 6A and 6BX connections on oil and gas wells.

Hot service

F5 and stainless rings for high-temperature lines.

Valves

RTJ-ended valves and fittings.

Turnarounds

New rings for every joint opened during a shutdown.

Traceable supply

Rings marked with type, number and material.

Supplied with the bolting

RTJ flanges carry heavy stud bolts; we supply them together.

  • A193 B7 and B16 stud bolts
  • A194 2H and 4 nuts
  • B7M and 2HM for sour service
  • Coated studs for offshore
  • Packed and tagged per joint

Shutdown bolting kits

Documents with every order

Ring type, number and material are checked against the line class before dispatch.

  • Manufacturer’s certificate
  • Hardness test results
  • Material certificate
  • Marking check
  • Third-party inspection on request

Quality and certificates

RTJ gasket questions

Why must an RTJ ring be softer than the flange?

The ring seals by deforming into the groove. If it were harder than the flange, it would damage the groove instead, so ring makers recommend a ring softer than the flange material.

Can R and RX rings be swapped?

They fit the same octagonal groove, but the make-up distance between the flanges is different, so RX is not a one-for-one replacement for R without checking the joint.

Can an RTJ gasket be reused?

No. Solid metal rings deform when they seal, so a new ring is fitted every time the joint is opened.

What does the D or S on a ring mean?

It is the material identification: D for soft iron and S for low-carbon steel. Stainless rings are marked by grade, for example S304 or S316 (304 or 316 under API 6A).

Which RTJ type does Saudi Aramco specify?

The 2018 issue (unofficial copy) of SAES-L-109 calls for octagonal Type R ring joint gaskets per ASME B16.20 for API 6B and ASME RTJ flanges.

Updated

Related

Spiral wound gaskets

ASME B16.20 gaskets for raised-face flanges.

A193 B16 stud bolts

High-temperature studs for hot RTJ joints.

Flanges

ASME B16.5 flanges including RTJ facings.

Need rings for a shutdown?

Send the ring numbers or the flange list: we quote rings, stud bolts and nuts together.

Request a quote+966 54 614 8678