ASTM F436 hardened steel washers
Through-hardened washers for structural and high-strength bolts, in carbon steel Type 1 and weathering steel Type 3, circular, beveled, clipped or extra thick, plain or galvanized to match the bolts.
ASTM F436 covers hardened steel washers for use with structural bolts such as F3125 A325 and A490, and with other high-strength bolts and nuts. Washers up to 1 1/2 in. are through hardened to 38 to 45 HRC, or 26 to 45 HRC when hot-dip galvanized. Type 1 is carbon steel and Type 3 is weathering steel for Type 3 bolts. The inch and metric washers have been in one standard, F436/F436M, since 2016.
- Standard
- ASTM F436/F436M (latest edition)
- Types
- Type 1 carbon steel; Type 3 weathering steel
- Styles
- Circular, square or rectangular beveled, clipped, extra thick
- Hardness
- 38 to 45 HRC through hardened; 26 to 45 HRC hot-dip galvanized
- Sizes
- Circular 1/4 to 4 in. and M12 to M100; beveled 1/2 to 1 1/2 in.
- Finish
- Plain, hot-dip galvanized (F2329) or mechanically galvanized (B695 Class 55)

What we supply
- Circular
- Standard round hardened washers
- Beveled
- Square washers with a 1:6 slope for tapered flanges
- Clipped
- Washers with one side cut for tight spaces
- Extra thick
- 5/16 in. washers for oversized holes
F436 washer styles
The style depends on the steel surface under the nut and the space around the bolt.
| Style | Shape | Sizes | Use |
|---|---|---|---|
| Circular | Round | 1/4 to 4 in., M12 to M100 | Standard structural and high-strength bolting |
| Beveled | Square or rectangular, 1:6 slope | 1/2 to 1 1/2 in., M12 to M16 | Tapered flanges of American standard beams and channels |
| Clipped | Circular or beveled with one side cut | As the circular or beveled style | Where space is tight; clipped edge no closer than 7/8 of bolt diameter to the centre |
| Extra thick | Round, 5/16 in. nominal | 1/2 to 4 in. | Oversized holes, and other holes where the connection design calls for them |
Summarised from ASTM F436/F436M as published by washer manufacturers. Washers over 1 1/2 in. may be through hardened or carburized.
Saudi Arabia requirements for structural washers
Saudi Aramco covers structural bolting in 12-SAMSS-007. The points below are from unofficial copies of older issues; we supply to the revision named in your purchase order.
| Requirement | What it means for the order |
|---|---|
| A325 assemblies | A325 bolts are used with A563 DH nuts and F436 washers. |
| Galvanizing | A325 bolts, nuts and washers are galvanized; A490 bolts are not galvanized. Washer finish for A490 assemblies follows the project specification. |
| Anchor bolts | Anchor bolts take plate washers to ASTM A36 (12-SAMSS-007, 2011 copy); F436 washers are supplied where the drawing calls for them. |
| Flange bolting | Flat washers on flange studs are used only in special cases, such as insulating flanges (SAES-L-109, unofficial 2018 copy). |
Based on unofficial copies of 12-SAMSS-007 (2011) and SAES-L-109 (2018), which may be superseded; confirm against the current revisions in your project specification and drawings.
Where F436 washers are used
Under the turned element of structural bolts and wherever a hard bearing surface is needed.
Steel connections
A325 and A490 bolted joints.
Oversized holes
Extra thick washers over oversized holes.
Anchor bolts
Washers under nuts on F1554 rods.
High-strength bolts
A354 and A449 bolts and studs.
Galvanized sets
Galvanized washers with galvanized bolts.
Bolt sets
Bolts, nuts and washers per connection.
Matched to the bolt set
Washers are supplied in the same type and finish as the bolts and nuts.
- Type 1 with Type 1 bolts
- Type 3 with weathering bolts
- Same galvanizing process
- Beveled and clipped styles
- Packed per connection
Documents with every order
Hardness results are reported for each lot.
- EN 10204 3.1 MTC
- Hardness test results
- Galvanizing thickness report
- Lot traceability
- 3.2 with third-party inspection
F436 washer questions
What hardness is an F436 washer?
Through-hardened F436 washers are 38 to 45 HRC. Hot-dip galvanized washers have a wider range of 26 to 45 HRC.
What is the difference between Type 1 and Type 3?
Type 1 is carbon steel. Type 3 is weathering steel, used with weathering-steel Type 3 structural bolts.
Is there a separate F436M standard?
Not any more. The metric washers were merged into F436/F436M in 2016, and F436M was withdrawn.
When is a beveled washer needed?
When the bolt bears on a tapered flange, such as an American standard beam or channel with a 1:6 slope.
Can F436 washers be galvanized?
Yes, by hot-dip galvanizing to F2329 or mechanical galvanizing to B695 Class 55, normally with the same process as the bolts and nuts.
Updated
Related
ASTM A563 nuts
DH and C nuts for structural bolts.
F3125 A325 and A490 bolts
Structural bolts for F436 washers.
Washers
Flat, spring and special washers.
Need washers with your bolts?
Send the bolt list: we quote bolts, nuts and F436 washers as matched sets.