Tap-end studs for valves, pumps and machine housings
Studs with a short tap end that screws into a tapped hole and a longer nut end, made to ASME B18.31.2 or to your drawing in A193 B7, B7M, B16 and stainless grades in our factory in Al-Jubail.
A tap-end stud has a short thread on one end that is screwed into a tapped hole, and a longer thread on the other end that takes the nut. ASME B18.31.2 covers it as the tap-end type of double-end stud, with either regular or interference-fit threads on the tap end. Tap-end studs are rarely stock items: thread lengths, fit and point details usually come from the equipment drawing, and the grade is chosen separately, commonly A193 B7, B7M, B16 or B8/B8M.
- Standard
- ASME B18.31.2 (tap-end type double-end studs) or customer drawing
- Grades
- ASTM A193 B7, B7M, B16, B8 and B8M; A320 L7 for cold service
- Tap end
- Short thread into the tapped hole: regular thread (often class 3A) or interference-fit thread (NC5), per drawing
- Nut end
- Usually the longer thread, for the nut; class 2A
- Metric
- Metal-end lengths of about 1 x d or 1.25 x d (DIN 938 / 939 style) to drawing
- Nuts
- A194 2H, 2HM, 4 or 8M to match the stud grade

What we supply
- Tap-end studs
- Short tap end and long nut end, to drawing
- Double-end studs
- Equal threads both ends for through holes
- Studs with nuts
- Matching A194 nuts and washers
- Replacement sets
- Studs copied from a sample or old drawing
Tap-end, double-end and full-thread studs
The thread layout depends on how the stud is installed. ASME B18.31.2 covers all three types.
| Type | What it is | Typical use |
|---|---|---|
| Tap-end stud | Short tap end screwed into a tapped hole, longer nut end | Valve bodies and bonnets, pump bodies, machine housings |
| Double-end (clamping) stud | Same thread length and form on both ends | Clamping parts through holes with a nut each side |
| Full-thread stud | Threaded over its whole length | Flange bolting with two heavy hex nuts |
The tap end has a regular thread (often a closer class 3A) or an interference-fit thread (NC5), per drawing. It is the interference fit, not class 3A, that keeps the stud in the hole when the nut is removed.
Ordering tap-end studs for Saudi plants
Tap-end studs usually replace bolting on existing equipment, so the order has to match the original part exactly.
| Item | Why it matters |
|---|---|
| Grade and nut | Same grade as the equipment maker specified, for example B7 with 2H or B16 with grade 4 nuts. |
| Tap-end thread and fit | Regular or interference fit, and the thread length engaged in the hole. |
| Nut-end and overall length | Nut-end thread length and total length, measured overall. |
| Sour service | Where the stud may be wetted by sour fluid, a hardness-limited grade such as B7M with 2HM nuts, as the equipment or project specification requires. (SAES-L-109 Table 5, in an unofficial 2018 copy, lists B7M/2HM for wet-sour flange bolting.) |
| Sample or drawing | An old stud or the equipment drawing lets us copy the exact geometry. |
We make tap-end studs to the equipment drawing; the equipment maker’s or project specification is the final word on grade. Based on an unofficial copy of SAES-L-109 (29 January 2018), which may be superseded; confirm against the current revision in your project specification.
Where tap-end studs are used
Anywhere a stud goes into a threaded hole in a casting or forging instead of through a flange.
Valve bodies and bonnets
Bonnet studs screwed into the valve body.
Pump bodies
Casing and cover studs on process pumps.
Machine housings
Covers and end plates on pumps and machine housings.
High temperature
B16 studs for hot valve bodies and bonnets.
Pressure parts
Inspection covers and special flanges.
Maintenance
Replacement studs copied from a worn sample.
Made to your drawing
We cut, thread and mark tap-end studs in Al Jubail from certified bar.
- Tap end and nut end to drawing
- Class 3A or interference-fit tap end
- Grade marking on the nut end
- Matching nuts supplied
- Small batches for maintenance
Documents with every order
Every batch is traced to its bar heat number.
- EN 10204 3.1 MTC
- Dimensional report
- Thread gauge check
- Hardness test results
- 3.2 with third-party inspection
Tap-end stud questions
What is a tap-end stud?
A stud with a short thread on one end that screws into a tapped hole and a longer thread on the other end for the nut.
Is there a standard for tap-end studs?
Yes. ASME B18.31.2 covers them as the tap-end type of double-end stud, with regular or interference-fit threads on the tap end. Many are also made to the equipment drawing.
What grade should a tap-end stud be?
The same grade the equipment calls for, commonly ASTM A193 B7, B7M for sour service, B16 for high temperature, or B8/B8M stainless.
Is the tap end threaded differently?
Often. The tap end may have a regular thread, often a closer-tolerance class 3A, or an interference-fit thread (NC5). The interference fit is what keeps the stud in the hole when the nut is undone; a 3A thread alone does not lock it. The fit is taken from the equipment drawing.
Can you copy a stud from a sample?
Yes. Send the old stud or a photo with dimensions, and we confirm the thread, lengths and grade before making the batch.
Updated
Related
A193 B7 stud bolts
A common grade for tap-end studs.
A193 B16 stud bolts
High-temperature studs for hot valve and pump joints.
Stud bolts
All stud grades and types.
Need tap-end studs made?
Send the drawing or a sample stud: we confirm thread, fit and grade, then quote.