+966 54 614 8678 [email protected] WhatsApp
JTE FastenersBolting & hardware, Al Jubail العربية Request a quote

DIN 931 and DIN 933 hex bolts, now ISO 4014 and ISO 4017

Partly threaded (DIN 931) and fully threaded (DIN 933) metric hex bolts, supplied to the current ISO 4014 and ISO 4017 standards in carbon steel classes 8.8 and 10.9 and in A2 and A4 stainless, plain or coated.

DIN 931 is a partly threaded hex bolt and DIN 933 is a hex screw threaded up to the head. Both DIN standards have been cancelled and replaced by ISO 4014 and ISO 4017. The ISO bolts are interchangeable with the old DIN ones except for the width across flats at four sizes: M10, M12, M14 and M22. An M12 DIN 933 bolt takes a 19 mm spanner, while an M12 ISO 4017 bolt takes 18 mm. Much stock sold as DIN 933 today is actually made to ISO 4017, so tell us which you need.

DIN 931
Partly threaded hex bolt, replaced by ISO 4014
DIN 933
Fully threaded hex screw, replaced by ISO 4017
Current ISO editions
ISO 4014:2022 and ISO 4017:2022, M1.6 to M64
Carbon steel
ISO 898-1 property classes 8.8 and 10.9; other classes to order
Stainless
ISO 3506-1 A2-70, A4-70 and A4-80
Finish
Plain, zinc plated, hot-dip galvanized or zinc flake
Row of zinc-plated hex bolts
Zinc-plated hex bolts (photo for illustration)

What we supply

Partly threaded
DIN 931 / ISO 4014 hex bolts
Fully threaded
DIN 933 / ISO 4017 hex screws
Nuts and washers
DIN 934 / ISO 4032 nuts and flat washers
Special lengths
Non-stock lengths cut and threaded to order

DIN and ISO across-flats differences

These four sizes changed when DIN was replaced by ISO. Check the spanner size before ordering spares for existing plant.

Width across flats, DIN 931/933 versus ISO 4014/4017
ThreadDIN 931 / 933ISO 4014 / 4017Difference
M1017 mm16 mmISO 1 mm smaller
M1219 mm18 mmISO 1 mm smaller
M1422 mm21 mmISO 1 mm smaller
M2232 mm34 mmISO 2 mm larger

All other sizes have the same across-flats in DIN and ISO. The same four sizes changed on hex nuts (DIN 934 to ISO 4032).

All hex boltsThread pitch chart

Strength classes for DIN 933 / ISO 4017 bolts

The product standard fixes the shape; the property class or stainless grade fixes the strength.

Common property classes
Class or gradeMaterialTensile minTypical use
8.8Carbon or alloy steel, quenched and tempered800 MPa (830 MPa above M16)General machinery and steelwork
10.9Carbon steel with additives or alloy steel, quenched and tempered1040 MPaHighly loaded joints
A2-70304-type stainless700 MPaIndoor and inland corrosion resistance
A4-80316-type stainless800 MPaCoastal and chloride exposure

Steel classes to ISO 898-1, stainless to ISO 3506-1. Class 9.8 was removed from ISO 4014 in its 2022 edition.

Class 8.8, 10.9 and 12.9 boltsA2 and A4 stainless bolts

Ordering DIN and ISO hex bolts in Saudi Arabia

Older equipment drawings often quote DIN numbers; current stock is usually made to ISO. A few details on the order avoid wrong spares.

What to state on a DIN or ISO hex bolt order
PointWhy it matters
DIN or ISOState which standard; at M10, M12, M14 and M22 the spanner size differs.
Thread lengthDIN 931 / ISO 4014 is partly threaded; DIN 933 / ISO 4017 is threaded to the head.
Property class8.8 or 10.9 for carbon steel; A2-70 or A4-80 for stainless.
FinishElectroplated zinc for indoor use; hot-dip galvanized or zinc flake outdoors.
MarkingBolts are marked with class or grade and maker; unmarked bolts are often rejected on site.

We supply to the standard on your order and confirm the across-flats before supply.

Where DIN 931 and 933 bolts are used

The everyday metric hex bolt in machinery, equipment and light steelwork.

Machinery

Pumps, motors, gearboxes and skids.

European equipment

Spares for plant built to DIN.

Light steelwork

Brackets, frames and supports.

Stainless fixings

A2 and A4 bolts in corrosive areas.

Outdoor bolting

Galvanized and zinc flake coated bolts.

Maintenance stock

Bolts, nuts and washers in common sizes.

DIN or ISO, your choice

We confirm the across-flats before supply so spares fit the existing spanners.

  • ISO 4014 and 4017 stock
  • DIN across-flats on request
  • Classes 8.8, 10.9 and 12.9
  • A2 and A4 stainless
  • Matching nuts and washers

Hex bolts

Documents with every order

Class and standard are shown on every certificate.

  • EN 10204 3.1 MTC
  • Mechanical test results
  • Dimensional check
  • Coating report if coated
  • 3.2 with third-party inspection

Quality and certificates

DIN 931 and 933 questions

What is the difference between DIN 931 and DIN 933?

DIN 931 bolts are partly threaded, with a plain shank under the head. DIN 933 bolts are threaded right up to the head.

Is DIN 933 still a valid standard?

No. DIN 933 was cancelled and replaced by ISO 4017, and DIN 931 by ISO 4014. The names are still widely used when ordering.

Are DIN 933 and ISO 4017 bolts interchangeable?

Yes, except that the width across flats is different at M10, M12, M14 and M22, so a different spanner is needed at those sizes.

What spanner fits an M12 bolt?

19 mm for DIN 933 and 18 mm for ISO 4017.

Which strength class should I order?

Class 8.8 is the general-purpose choice for carbon steel; 10.9 for highly loaded joints; A2-70 or A4-80 where corrosion resistance is needed.

Updated

Related

Class 8.8, 10.9 and 12.9 bolts

ISO 898-1 property classes.

A2 and A4 stainless bolts

ISO 3506 stainless bolts.

Zinc flake coated bolts

Thin corrosion-resistant coating for high-strength bolts.

Need metric hex bolts?

Send the size list and tell us DIN or ISO: we quote bolts, nuts and washers together.

Request a quote+966 54 614 8678