+966 54 614 8678 [email protected] WhatsApp
JTE FastenersBolting & hardware, Al Jubail العربية Request a quote

ASTM A307 Grade A and Grade B bolts

Low-carbon steel hex bolts, studs and threaded rod with a 60 ksi minimum tensile strength, plain or galvanized, for handrails, ladders, girts and other secondary connections, and Grade B for cast-iron flanged joints.

ASTM A307 covers carbon steel bolts, studs and threaded rod with a 60 ksi (414 MPa) minimum tensile strength, in sizes 1/4 to 4 in. Grade A is for general use. Grade B, with a tensile range of 60 to 100 ksi, is for flanged joints in piping with cast-iron flanges. A307 sets no yield strength, so it is not a high-strength structural bolt. The former Grade C for anchor bolts was replaced by ASTM F1554 Grade 36 in 2007.

Standard
ASTM A307-21
Grades
A: general use; B: cast-iron flanged piping joints
Tensile
Grade A 60 ksi min; Grade B 60 to 100 ksi
Sizes
1/4 to 4 in.
Nuts
A563 Grade A hex for Grade A up to 1 1/2 in.; heavy hex above that and for Grade B
Finish
Plain or hot-dip galvanized
Hex bolt and nut, black and white close-up
Hex bolt and nut (photo for illustration)

What we supply

Hex bolts
Grade A hex and heavy hex bolts
Grade B bolts
Bolts and studs for cast-iron flanges
Threaded rod
A307 rod and studs cut to length
Sets
Bolts with A563 nuts and washers, galvanized as needed

A307 Grade A and Grade B

Both grades are low-carbon steel. Grade B has a maximum tensile and a lower maximum hardness, for flanged joints in cast-iron piping.

ASTM A307 mechanical properties
PropertyGrade AGrade B
Tensile strength60 ksi min60 to 100 ksi
Yield strengthNot specifiedNot specified
Elongation in 2 in.18% min18% min
Hardness (length under 3d)121 to 241 HB121 to 212 HB
Default nutA563 Grade A hex or heavy hexA563 Grade A heavy hex
Typical useSecondary steel and general boltingCast-iron flanged piping joints

Values summarised from ASTM A307-21 as published by bolt manufacturers.

All hex boltsA563 nuts

Saudi Arabia limits on A307 bolts

Saudi Aramco limits where A307 bolts can be used. The points below are from older issues of its standards; confirm against the current revisions in your project specification.

A307 bolts on Saudi Aramco projects
RequirementWhat it means for the order
Primary connectionsA325 Type 1 high-strength bolts are used in all primary bolted connections, not A307.
Secondary connectionsA307 may be used for ladder, stair tread, purlin, girt, door frame and handrail connections.
Size limitA307 bolts are limited to 16 mm (5/8 in.) and smaller.
Anchor boltsThe 2011 copy of 12-SAMSS-007 lists headed anchor bolts in A307 Grade A, while SAES-M-100 (2009 copy) excludes anchor bolts from its A307 clause. Anchor bolt material comes from the anchor bolt drawing and needs project approval.
GalvanizingA307 bolts, nuts and washers are galvanized to F2329 or B695.

Based on unofficial copies of SAES-M-100 (2009), SAES-M-001 (2019) and 12-SAMSS-007 (2011), which may be superseded; confirm against the current revisions in your project specification. Unmarked bolts and nuts are rejected on Aramco sites.

Where A307 bolts are used

Light-duty connections where strength is not critical, and cast-iron flanges that would crack under high-strength bolts.

Secondary steel

Girts, purlins and door frames.

Access steel

Ladders, stair treads and handrails.

Cast-iron flanges

Grade B bolts for cast-iron piping joints.

General bolting

Light equipment, brackets and supports.

Galvanized sets

Outdoor bolting at coastal sites.

Bolt sets

Bolts, nuts and washers per connection.

The right bolt for the joint

A307 is economical, but it is not a structural high-strength bolt, so we check the application.

  • Grade A or B as specified
  • A325 offered for primary connections
  • F1554 Gr 36 for anchor rods
  • Galvanized with oversize nuts
  • Cut-to-length studs and rod

F3125 A325 bolts

Documents with every order

Marked, certified bolts accepted on site.

  • EN 10204 3.1 MTC
  • Tensile and hardness results
  • Galvanizing thickness report
  • Marking check
  • 3.2 with third-party inspection

Quality and certificates

A307 bolt questions

What is the difference between A307 Grade A and Grade B?

Grade A has a 60 ksi minimum tensile for general use. Grade B has a 60 to 100 ksi range and lower maximum hardness, for flanged joints in piping with cast-iron flanges.

Is A307 a structural bolt?

It is used in light structural connections, but it is not a high-strength bolt and has no specified yield strength. Primary connections use A325 or A490 (F3125).

What happened to A307 Grade C?

It was removed in 2007 and replaced by ASTM F1554 Grade 36 for anchor bolts.

Which nut goes with A307 bolts?

ASTM A563 Grade A hex nuts for Grade A up to 1 1/2 in., and A563 Grade A heavy hex nuts above that and for Grade B. Stronger nuts are also acceptable.

Can A307 bolts be used on Saudi Aramco projects?

In the older Saudi Aramco standards we have seen (unofficial copies of SAES-M-100, SAES-M-001 and 12-SAMSS-007), A307 is limited to secondary items such as ladders, stairs, girts, purlins and handrails, typically 16 mm (5/8 in.) and smaller. Check the current project specification.

Updated

Related

ASTM A563 nuts

Grade A nuts for A307 bolts.

F3125 A325 and A490 bolts

High-strength bolts for primary connections.

ASTM F1554 anchor bolts

Grade 36 replaced A307 Grade C.

Need bolts for secondary steel?

Send the bolt list: we quote A307 or A325 bolts with nuts and washers, plain or galvanized.

Request a quote+966 54 614 8678